OM-1068-001.pdf - 第164页

0005-002 Chapter 3 2-3 Tg0252-PM-SO A : Error Message B : Details of Error Message C : Guidance to the Cause and Remedy of Error (Some errors may not be displayed.) Refer to “4. T roubleshooting after Error Messages of S…

0005-002 Chapter 3 2-2 Tg0252-PM-SO

1. ERROR Display

When a device in operation is interrupted or stopped in an error condition

(error condition detected as impossible to continue the operation), an “ER-

ROR” display (Fig. 3.2) appears on the screen.

The same display also appears on the operation monitor of the main machine.

Refer to “Error Messages of Section 2 in Volume 3” in the main machine

instruction manual for details.

• When an error occurs during automatic operation, the tower light of the

main machine illuminates (standard setting) and an “ERROR” display ap-

pears on the screen. The “ERROR” display also appears when an error oc-

curs while a device is running (while the LEDs of the [START], [MOVE],

[ZERO], and [READY] buttons are ON).

Fig. 3.1

Fig. 3.2

“Occurrence of Error”

1. ERROR Display

0005-002 Chapter 3 2-3 Tg0252-PM-SO

A : Error Message

B : Details of Error Message

C : Guidance to the Cause and Remedy of Error

(Some errors may not be displayed.)

Refer to “4. Troubleshooting after Error Messages of Section 2 in Chapter 3”

for details (error messages, details of error messages, cause, remedy, etc.).

D : This key is used to stop buzzer sound.

E : Buzzer sound stops and the display before an error has occurred resumes.

2. Remedial Procedure after Error Display

Operation Procedure

(1) Press the [BUZZER STOP] key.

(See Fig. 3.2.)

The buzzer stops sounding.

(2) Check the contents of the error message and the remedial procedure

(GUIDANCE TO CAUSE AND REMEDY) displayed on the operation

monitor.

Ref.: “4. Troubleshooting after Error Messages of Section 2 in Chapter

3” for details.

(3) Remove the cause of the error.

Different countermeasures and remedial procedures must be taken,

depending on the type of an error.

• Remedial Procedure when power must be re-supplied or the system

clear operation must be performed

(1) Refer to “6.7.2 Reset and Start Procedure from Emergency Stop

of Section 2 in Volume 1” in the main machine instruction

manual for details.

• Remedial Procedure when the zeroing operation must be performed

(1) Press the [RTN] key.

(2) Perform the zeroing operation.

Refer to “2. Zeroing Operation of Section 4 in Chapter 1” for

details.

• Remedial Procedure when the cause of an error is removed without

performing the zeroing or the system clear operation or just for

message confirmation

(1) Press the [RTN] key.

(2) The display before the “ERROR” display resumes.

(3) Refer to the instructions (GUIDANCE TO CAUSE AND

REMEDY) and remove the cause.

2. Remedial Procedure after Error Display

0005-002 Chapter 3 2-4 Tg0252-PM-SO

3. Error Messages

Main Section Error Messages (

)

11H Traverse 1 01H

02H

03H

04H

05H

06H

TV1-AXIS ORIGIN

TV1-AXIS TIMING

TV1-AXIS DATA

TV1-AXIS LIMIT

TV1-AXIS INTERLOCK

POWER ON MONITOR

12H Traverse 2 01H

02H

03H

04H

05H

06H

TV2-AXIS ORIGIN

TV2-AXIS TIMING

TV2-AXIS DATA

TV2-AXIS LIMIT

TV2-AXIS INTERLOCK

POWER ON MONITOR

13H Elevator 1 01H

02H

03H

04H

05H

06H

07H

08H

EV1-AXIS ORIGIN

EV1-AXIS TIMING

EV1-AXIS DATA

EV1-AXIS LIMIT

EV1-AXIS SERVO

EV1-AXIS INTERLOCK

MAGAZINE CONNECTION

POWER ON MONITOR

14H Elevator 2 01H

02H

03H

04H

05H

06H

07H

08H

EV2-AXIS ORIGIN

EV2-AXIS TIMING

EV2-AXIS DATA

EV2-AXIS LIMIT

EV2-AXIS SERVO

EV2-AXIS INTERLOCK

MAGAZINE CONNECTION

POWER ON MONITOR

6FH Multi-Layer Tray

Feeder (L)

01H SHORTAGE OF COMPONENT

FOR TRAY-L

70H Multi-Layer Tray

Feeder (R)

01H SHORTAGE OF COMPONENT

FOR TRAY-R