OM-1068-001.pdf - 第101页

5. Preparation and Confirmation before Operation Tg0252-PM-SO (4) Press the black circle point shown in the label in Fig. 1.21-2 to close the magazine door . (5) Confirm that the magazine door is latched. (Fig. 1.21-4) F…

5. Preparation and Confirmation before Operation

Tg0252-PM-SO

5.2.2.2 Pallet Attachment to Magazine

(1) Push both handles of the magazine door fixture down in direction

shown by an arrow A and release the lock of the magazine door.

(Fig. 1.19-1 and Fig. 1.19-2, Arrow A)

(2) Open the magazine door. (Fig. 1.19-3 Arrow B)

Note: (a) Because the magazine door might become deformed

by impact, open it gently, holding the grip. If operation

is started with a deformed magazine door, it might

cause machine breakdown.

(b) Do not place any thing on the open door or put any

pressure on it.

(3) Set the pallet equipped with a tray in the magazine.

Put the pallet on the partition plate and push it inside.

Fig. 1.19-2 Latched

Magazine Door

Fixture

Fig. 1.19-3 Unlatched

Magazine Door

Fixture

Grip

Fig. 1.19-1 How to open the magazine door

When a pallet is set in the magazine, note the direction of the cutout and

do not set the pallet upside down.

(See Figs. 1.20-1 and 1.20-2.)

When the [U READY] or the [L READY] button is pressed with the pallet

not oriented correctly, the error is detected. However, when the pallet is

inserted upside down, the error is not detected, causing a failure.

The contents of the error are displayed on the operation monitor.

CAUTION

0112-004 Chapter 1 2-17

Fig. 1.20-2 MG-5050L (For FP-5021L)

Fig. 1.20-1 MG-5050R (For FP-5021R)

Coutout of Pallet

Side without

Side Plate

Side without

Side Plate

Cutout of Pallet

Side Plate Side

Pallet Drawing

Direction

Pallet Drawing

Direction

5. Preparation and Confirmation before Operation

Tg0252-PM-SO

(4) Press the black circle point shown in the label in Fig. 1.21-2 to

close the magazine door.

(5) Confirm that the magazine door is latched.

(Fig. 1.21-4)

Fig. 1.21-1

Fig. 1.21-2

If the magazine door is closed roughly, components might be bumped

out of the tray. Close it gently and securely.

If the magazine door is not latched securely, it may open suddenly dur-

ing operation (while the machine is running), causing some damage to

the machine.

CAUTION

0112-003 Chapter 1 2-18

5.2.2.3 Pallet Detachment from Magazine

(1) Push both handles of the magazine door fixture down in direction shown

by an arrow A and release the lock of the magazine door. (Fig. 1.19-1 and

Fig. 1.19-2, Arrow A)

(2) Open the magazine door.

(Fig. 1.19-3 Arrow B)

(3) Pull out the pallet to be detached.

Fig. 1.21-3 Unlatched Magazine Door

Fixture

Fig. 1.21-4 Latched Magazine Door Fixture

5. Preparation and Confirmation before Operation

Tg0252-PM-SO

5.2.2.4 Partition Plate Removal Procedure in Even Steps

• When a component of 11.5 mm or more in height is placed on the

tray t1or t2, the partition plate (even steps) should be detached to

avoid interference of the partition plate with the component.

(1) Pull the grip of the magazine door fixture down in the di-

rection of Arrow A to unlatch the magazine door. (Figs.

1.19-1 and 1.19-2 Arrow A)

(2) Open the magazine door. (Fig. 1.19-3 Arrow B)

(3) Remove the bolts fixing the partition plate and remove the

plate.

Notes : (a) When the partition plate is removed, confirm

the step No. and remove the partition plate

only at the even steps. If the partition plate

at the odd stage is removed and the pallet is

set there, the pallet can’t be drawn out from

the magazine during operation.

(b) The partition plate and bolts, which have

been removed will be used when the parti-

tion plate is installed again. Set aside with

care. Also, handle the partition plate care-

fully because it is easily deformed.

Enlarged Figure (Same condition on the right side)

Fig. 1.22

Fig. 1.23

Right

Side

Left

Side

Bolt

Step No.

Partition Plate

Component

0112-004 Chapter 1 2-19