YCP10 Users_E.pdf - 第110页

4-14 4 Daily operation 6.3 Long-term storage tasks If the solvent pump is not used for extended periods (about 6 months or more), then it ma y dry out internally and cause operating defects. T he solvent path within the …

4-13

Daily operation

NOTE

When setting the solvent bottle for the ﬁrst time or when the solvent has not been used for an extended period of

time, follow the steps below to discharge the solvent to the gauze roll.

1. Select the [Cleaner] tab on the [Unit] screen.

2. Press the [Fuel Pump] button to discharge the solvent. When the solvent oozes from the gauze roll, this work is

completed.

[Unit] screen

[Cleaner] tab

[Fuel Pump] button

64408-N1-10

4-14

Daily operation

6.3 Long-term storage tasks

If the solvent pump is not used for extended periods (about 6 months or more), then it may dry out internally

and cause operating defects. The solvent path within the pump must be blocked to prevent this from happening.

The path blocking procedure is described below.

Blocking the solvent path

Remove the cleaner cover.

1. Remove two screws (dotted line portions

in the figure on the right) that secure the

cleaner cover.

2. Next remove the screws at 4 locations on

the near side (see drawing).

3. Raise the cover upward and then pull

toward you to remove it.

63413-N1-00

Remove the joints.

Remove the joints from two locations, one

on the head side and the other on the

bottle side from the shut-off valve joint. Use

caution because alcohol remaining in the

hose will come out when the joint on the

head side is removed.

1. Remove the head side joint in the bent

state as shown by the dashed line in the

figure on the right.

2. Prepare a container, free the bent

location and let the alcohol drain into

the container.

3. Remove the bottle side joint and then

quickly point it upward to let the alcohol

in the hose return back to the bottle.

63414-N1-00

Mark the hoses you removed.

Mark the two hose sections you removed in

step 2 by winding yellow ribbon or a similar

item around them.

63415-N1-10

Reattach the cleaner cover.

Reinstall the cleaner cover in the reverse of

the procedure that you removed it in step 1.

Place a ribbon on the outer side of the

cover so that others will know that the joints

were removed.

Resetting operation

Connect the hoses in the reverse of the "Blocking the

solvent path" procedure and refill with solvent by

referring to "6.2 Refilling the cleaning solvent" in this

Chapter. When finished refilling, operate the solvent

pump to make sure it operates correctly.

Removing the cleaner cover

Step 1

First, remove the screws at 2 locations.

Removing the joints

Step 2

Joint (to head)

Shut-off valve joint

Container

Joint (to bottle)

Hose markings

Step 3

Marking (yellow ribbon, etc.)

Marking

As seen from outside the cover

4-15

Daily operation

7. Compatible masks

7.1 Mask size and mask stopper pin position

The mask stopper pin position must be changed according to the mask frame size to be used as shown below.

One screw-type mask stopper pin sets the left end position of the mask frame. Screw this stopper pin into one

of the "F" positions when the front conveyor rail is fixed, or one of the "R" positions when the rear conveyor rail

is fixed.

Mask frame size and stopper pin position

Mask frame size

L (mm) × W(mm)

Applicable board dimensions

L (mm) × W(mm)

Mask frame stopper pin position

L direction W direction

750 × 750 L50 × W50 (min.) to L510 × W460 (max) A Not used.

750 × 650 L50 × W50 (min.) to L510 × W350 (max.) A 2 (2 locations)

736 × 736 L50 × W50 (min.) to L510 × W460 (max.) B 1 (2 locations)

650 × 550 L50 × W50 (min.) to L330 × W250 (max.) C 3 (2 locations)

600 × 550 L50 × W50 (min.) to L330 × W250 (max.) D Mask adaptor (option)*

584 × 584 L50 × W50 (min.) to L330 × W250 (max.) E Mask adaptor (option)*

550 × 650 L50 × W50 (min.) to L330 × W250 (max.) F Mask adaptor (option)*

*See "7.3 Using the mask adaptor" in this chapter for the mask adaptor (option).

TIP : Store the pins that are not in use.

B C DF

3 3

Mask frame size and stopper pin position

Mask clamp

Mask frame L

Mask frame W

63422-N1-10

Mask stopper pin

63423-N1-00