YCP10 Users_E.pdf - 第47页

1-6 1 Part names and functions 2.2 Operation display screen Machine oper ation and data editing procedures are performed at the operation displa y screen (touch-panel specifications). A touch pen is used to select the on…

1-5

Part names and functions

2.1 Operation panel buttons

The operation panel buttons are provided on the front and rear of the machine to run major commands

frequently used to operate the machine. Each button is lit while turned on. The colors used for the operation

panel are the same as those specified for the signal light (signal tower).

Operation panel buttons

63104-N1-00

Operation panel button functions

Button name Use the button to: OFF ON

READY

Release emergency stop and turn the

servo on.

• SERVO OFF

(Motor power OFF)

• SERVO ON

(Motor power ON)

RESET

Stop automatic operation and return to

standby for board production.

• Machine is in normal operation

or stopped.

• Machine has been reset.

START (green)

Perform operation according to board

data.

• Machine is stopped. • Machine is in normal operation.

STOP (Red / White)

Interrupt automatic operation. (Press

START to resume operation.)

• Machine is in normal operation. • Error occurred.

ERROR CLEAR

(Yellow / Blue)

Stop buzzer sound and clear error

screen.

• Machine is in normal operation. • Error occurred.

EMERGENCY STOP

Trigger emergency stop. Turn to the

right to release it.

1-6

Part names and functions

2.2 Operation display screen

Machine operation and data editing procedures are performed at the operation display screen (touch-panel

specifications). A touch pen is used to select the onscreen buttons and parameter items. Be sure to return the

touch pen to its holder when it is not in use.

Touch screen (option)

Operation display screen

(Touch-panel)

Holder

Touch pen

63105-N1-00

2.3 Keyboard (option)

An optional keyboard for operation and data editing, etc., can be added to the machine's configuration if

desired. The keyboard's track-ball is used to move the cursor to the desired onscreen buttons and parameter

items which are then selected by pressing the left-click button (right-clicking is not available).

When using the keyboard, install the bracket on this machine and connect the USB terminal of the keyboard to

the USB port on this machine.

Keyboard

Bracket

These USB ports are not allowed to use.

USB port for keyboard connection

Track-ball

Left/right button

63106-N1-00

CAUTION

The USB port shown in the illustration is for the keyboard only. (Only keyboards which do not require a -101 dedicated

driver are supported.) Do not connect other USB devices to this port.

Moreover, connecting 2 or more keyboards will disable exclusive access control, and therefore stop keyboard

operation.

CAUTION

Do not use the USB ports of the keyboard. The USB port may not operate correctly due to insufﬁcient power.

1-7

Part names and functions

3. Printing section

This machine uses a printing pressure feedback head and a highly rigid printing table to perform solder

paste printing at high speeds yet with high accuracy.

3.1 Squeegee head and printing table

Squeegee head and printing table

63107-N1-00

1. Squeegee head

Moves the squeegee vertically (along the SZ-axis) and forwards or backwards (along the SY-axis ). The 3S squeegee head

rotates slightly even in the R direction.

2. Squeegee holder

The squeegee can be easily mounted in this squeegee holder with two screws.

3. Mask clamp

Clamps a mask frame on the printing table. There are two clamps each on the left and right sides (a total of 4 clamps).

When using a small mask, attach the special adaptor at two locations on the rear.

4. Mask clamp switch

Turn this switch CCW or CW to release or clamp the mask.

5. Mask (prepared by user)

Various types of masks (stencils) with different frame sizes can be used by just changing the position of the stopper pin.

For information about the mask frame sizes and stopper pin positions, see "7.1 Mask size and mask stopper pin position"

in Chapter 4.

6. Handle

Use the handles on both sides to move the squeegee head forwards or backwards by hand during servo-off. Never move

the squeegee head by pushing it or the squeegee.