YCP10 Users_E.pdf - 第129页

4-33 4 Daily operation 11. Finishing board production T o finish board production, follow these steps. 1 Stop machine oper ation. (1) Automatic stop When the specified number of boards has been produced the machine autom…

4-32

Daily operation

Monitor: Filling

The [Filling] tab appears on the Monitor screen by selecting the [Print]-[Squeegee]-[Detail Setting] then press the [Edit]

button to set to "Use" for Filling Adjust(Dry).

[Monitor]-[Filling] tab

64421-N1-10

Filling Adjust (Dry) Counter, Filling Adjust (Wet) Counter, Filling Adjust (Manual) Counter

After dry auto cleaning or wet auto cleaning or manual cleaning has been carried out, the corresponding counter counts

up each time a board is printed while adjusting the solder filling. The counter is reset to "1" when it reaches the "Filling

Adjust Count" set on the "Squeegee Detail Setting" screen that appears with the [Print]-[Squeegee]-[Detail Setting]. The

count start number can be changed with the [Edit] button.

[Filling Adjust (Dry)] button, [Filling Adjust (Wet)] button, [Filling Adjust (Manual)] button

These buttons are left depressed (turned on) while solder filling is being adjusted, and the current printing step is shown

with light-blue in the right-hand list. These buttons automatically turn off when printing with solder filling is complete up

to the specified number of steps. The machine then returns to normal printing without adjusting the solder filling. (The

above screen shows that the first board after wet automatic cleaning is being printed while adjusting the solder filling.)

TIP

If two or more cleaning methods are designated at the same timing, the order of priority will be "Manual", "Wet Auto"

and "Dry Auto. For more details, see "6. Cleaner data setting" in Chapter 5.

Monitor: Print Inspection

The [Print Inspection] tab appears on the Monitor screen when the machine uses an optional solder-print inspection

function. You can check solder-print inspection results that are graphically and numerically displayed. For details, see

"Print inspection function" in the separate Option Manual.

4-33

Daily operation

11. Finishing board production

To finish board production, follow these steps.

Stop machine operation.

(1) Automatic stop

When the specified number of boards has been produced the machine automatically stops after

unloading the last board. Use this method in normal production. However, there may be cases (2) to

(5) as follows where you want or have to stop production prior to automatic stop.

(2) [Cycle Stop] button

Pressing the [Cycle Stop] button on the [Utility] tab of the Setup screen stops the machine operation

just after printing the current board. New boards are then no longer carried in from the upstream

side (loader, buffer conveyor, etc.).

(3) [Convey-out Stop] button

Pressing the [Convey-out Stop] button on the [Utility] tab of the Setup screen stops the machine

operation just after printing and unloading the current board. New boards are then no longer

carried in from the upstream side (loader, buffer conveyor, etc.).

(4) Emergency stop button

Pressing this button triggers emergency stop. Do not use this button in normal operation.

(5) [STOP] button (operation panel)

Pressing the [STOP] button stops the machine immediately as in emergency stop. To resume

operation, press the [START] button on the operation panel.

Press the [RESET] button on the operation panel to reset the operation.

Machine returns to board production standby status.

Clean the mask after board production.

1. Open the [Setup] tab or the Setup screen and press the [Auto Cleaning] button.

A screen appears to select the cleaning method.

2. Select the cleaning method ("Dry" or "Wet") and press the OK button.

The cleaning unit begins moving to clean the backside of the mask automatically.

TIP

If you want to perform manual cleaning, press the [Manual Cleaning] button and follow the message that appears.

Detach the squeegees.

1. Press the [Move Squeegee] button and move the squeegee head to the "Front Side" position.

2. After pressing the emergency button, open the upper door and detach the squeegees from the

holder by loosening the mount knobs.

Remove the mask from the printing table.

Press [Mask Clamp] button to unclamp the mask and then remove it from the printing table.

Close the upper door and cancel emergency stop.

4-34

Daily operation

Quit the software.

Press the [Off] button on the operation display and follows the message that appears on the screen.

[Off] button

64422-N1-10

Turn off the power switch on the front right of the machine.

See "2.3 Powering off the machine" in Chapter 2.

Clean the squeegees and mask.

After detaching the squeegees and mask, clean them with the appropriate cleaner and

wiper(available as option) to wipe way the remaining solder and flux.

CAUTION

Take precautions when handling solvents. See "1.9 Handling solvents (including solder and adhesive)" in Safety

instructions.

NOTE

To ﬁnd how to correctly handle the mask and solder, refer to the instruction manual of the mask or solder

manufacturer.

CAUTION

How well you clean the mask you detached after use will greatly affect the production yield the next time that same

mask is used. Also handle the squeegee and mask carefully to avoid dents and scratches.