YCP10 Users_E.pdf - 第228页
7-18 7 Other functions 4.1 "Move Axis" screen Pressing the [Axis] button on the Unit screen opens the "Move Axis" screen as shown below . T he selecting tabs "X1/X2", "Y/Z", "…
7-17
7
Other functions
4. Manual operation
When you press the [Unit] button, the following screen appears. This screen is divided by several tabs such
as [Conveyor], [Mask], [Squeegee] and [Cleaner] to allow manually operating the servo-controlled units. You
can also check the status of each sensor and I/O signal on the [I/O] tab screen.
Unit screen
Selection tab
64716-N1-10
7-18
7
Other functions
4.1 "Move Axis" screen
Pressing the [Axis] button on the Unit screen opens the "Move Axis" screen as shown below. The selecting tabs
"X1/X2", "Y/Z", "CX", "SY/SZ", and "SR",etc. are on the screen. The each axis can be operated manually with the
tabs.
"Move Axis" screen
Selection tab
64717-N1-00
Selection tab Function
X1/X2 Moves the board clamp table in the X direction.
Z/Y Moves the board clamp table in the Z (up/down) or Y direction.
CX Moves the board (print inspection) camera unit in the X direction.
SY/SZ Moves the squeegee head in the Y direction or moves it vertically.
SR Adjusts the 3S squeegee scraper angle. (3S squeegee only)
Width Adjusts the conveyor width.
PU Raises and lower the push-up plate.
MX Moves the mask camera along the board table in the X-direction.
CV Convey boards on the conveyor.
7-19
7
Other functions
n
Manual axis movement
This section describes how to use the buttons on the "Move Axis" screen, using the [SY/SZ] tab and [CV] tab as an
example.
"Move Axis" screen
[SY/SZ] tab, [CV] tab
4
2
5
3
1
64718-N1-00
1. SY-axis movement buttons, [PTP] button
Pressing the arrow buttons moves the squeegee head in the Y direction. When the [Step Mode] button is in the depressed
state, the squeegee head moves at the specified step stroke each time the arrow buttons are pressed.
Pressing the [PTP] button displays the "PTP" screen. You can directly specify the position where you want to move the
squeegee head. The current position is displayed in the "SY (mm)" box.
2. SZ-axis movement buttons, [PTP] button, [Brake] button
Pressing the arrow buttons moves the squeegee head vertically. When the [Step Mode] button is in the depressed state,
the squeegee head moves at the specified step stroke each time the arrow buttons are pressed.
Pressing the [PTP] button displays the "PTP" screen. You can directly specify the position (height) where you want to
move the squeegee head. The current position is displayed in the "SZ (mm)" box.
The [Brake] button turns the SZ-axis brake on or off.
3. [Step Mode] button
Press this button to set axis movement to "step mode (inching mode)". (The button will remain depressed until you press
it again to exit "step mode".)
Specify the step stroke (inching stroke) with the arrow button or enter it directly in the "Step Stroke" box.
4. "Speed (%)" box
Select the speed to move the unit.
5. [Reset] button ( [CV] tub only)
Performs a CV axis zero reset.
TIP
Operation of buttons on other tabs is basically the same. The Z-axis of the [Y/Z] tab, the SZ-axis of the [SY/SZ] tab, and
the [SR], [Width], and [PU] tabs have a [Brake] button that turns on or off the motor brake.
c
CAUTION
The X-axis and R-axis operate while the X1-axis is synchronized with the X2-axis. Therefore, when each axis is
operated individually, this axis becomes difficult to move to the target position.
To move the X-axis and R-axis, use the [PTP] button.