3OM-1003-005.pdf - 第346页

0305-001 5-59 AIL01EDTP *6 Output mode Select "Standard", "Interval", or "SEMEMA" to determine how to trans- fer a P .C.B. from the main machine to the output machine. Standard When the outp…

*5 Input conveyor

Timer #1 [sec], Timer #2 [sec], Stop timer [sec]

Set each parameter to specify how the input conveyor should work.

Timer #1 [sec]

Set the time to limit the operating time (P.C.B. reception from the

input machine) of the input conveyor.

This timer measures the operating time of the input conveyor and is

used to detect an interrupted P.C.B.

(a) Add 2 seconds (approx.) to the time required for P.C.B.

reception from the input machine and set the time in

the text box.

(b) The data input range is "0 to 99 seconds".

Timer #2 [sec]

Set the time to limit the operating time of the input conveyor to transfer

a P.C.B. on the main machine side.

This timer measures the operating time of the input conveyor and is

used to detect an interrupted P.C.B.

The data input range is "0 to 99 seconds"

Stop timer [sec]

Set the delay time (the period of time during which the sensor at the

buffer position of the input conveyor detects a P.C.B. and the con-

veyor stops) in the text box.

When a P.C.B. has a cutout as shown in the figure below and stops

at a position where the photosensor is located inside the cutout af-

ter it is detected by the photosensor, the system determines it as

there is no P.C.B. To avoid this, it is required to set the delay time.

Fig. 3E50

0305-001 5-58

AIL01EDTP

3.3 "Auto Operation" Tab

Photosensor

Cutout

P.C.B.

Note

0305-001 5-59 AIL01EDTP

*6 Output mode

Select "Standard", "Interval", or "SEMEMA" to determine how to trans-

fer a P.C.B. from the main machine to the output machine.

Standard

When the output machine is manufactured by us, set "Standard" in

the text box.

When the work request signal is received from the output machine,

the P.C.B. transfer signal of the machine is turned ON and a P.C.B.

is transferred to the output machine by the output conveyor.

When the work request signal is not turned OFF within the specified

time after a P.C.B. unloading action has started, the machine stops

in an error condition.

Interval

When the work request signal of the output machine is turned ON,

P.C.B.’s on the machine side are transferred to the output machine.

The conveyor stops when the output conveyor timer has reached

the specified time.

The machine starts its unloading actions when the unloading condi-

tion is fulfilled after the conveyor has stopped running and the time

specified in the "Output interval timer [sec]" text box has elapsed.

No error detection is made.

SMEMA (Not Available)

P.C.B.’s are transferred according to the "SMEMA" standard.

*7 Output conveyor

Timer #1 [sec], Timer #2 [sec], Stop timer (Buffer #1) [sec], Stop

timer (Buffer #2) [sec]

Timer #1 [sec]

Set the time to limit the operating time (P.C.B. reception by the out-

put machine) of the output conveyor.

(a) Add 2 seconds (approx.) to the time required for P.C.B.

reception by the output machine and set the time in the

text box.

(b) The data input range is "0 to 99 seconds".

Timer #2 [sec]

Set the time to limit the operating time of the output conveyor to

transfer a P.C.B. on the main machine side.

The data input range is "0 to 99 seconds"

3.3 "Auto Operation" Tab

Note

Stop timer (Buffer #1) [sec]

Set the delay time (the period of time during which the sensor at the

buffer 1 position of the output conveyor detects a P.C.B. and the

conveyor stops) in the text box.

Stop timer (Buffer #2) [sec]

Set the delay time (the period of time during which the sensor at the

buffer 2 position of the output conveyor detects a P.C.B. and the

conveyor stops) in the text box.

*8 Output interval timer [sec]

When "Interval" is set in the "Output mode" text box, set the time as

interval time for P.C.B. unloading actions.

The data input range is "0 to 99 seconds".

Fig. 3E51

*9 Buffer conveyor count [pcs]

Set the number of P.C.B. buffers on the input conveyor in this text

box.

"1" or "2" can be set in the text box.

*10 # of Buffereds P.C.B.’s to be discharged [pcs]

Set the number of P.C.B.’s that can be held in reserve ready for

production on the output conveyor.

Set "1" or "2" in the text box.

0305-001 5-60

AIL01EDTP

3.3 "Auto Operation" Tab

Note