00198178-04_GS_FeederManager_3.3_R18-1_EN.pdf - 第148页
SIPLACE Feeder Ma nager 3.3 (R18 -1) / Getting S tarted 08/2018 Edition 148 How long does this proc edure last? No asset losses W hat is the purpose of Feeder Exchanged W orkflow? The Feeder Exchang ed workflow is bein…
SIPLACE Feeder Manager 3.3 (R18-1) / Getting Started 08/2018 Edition
147
15.3 Repair
Questions
Answers
Target/Benefit
Which feeders are defective?
Where are they located?
Alert List
Feeder Maintenance Defect
Report
Feeder Summary Report
Grouped By Location
Ensure that defective
feeders are separated
from good feeders
Avoid double work and
downtime
What error indication is
displayed for the feeder (what
can the operator find out)
Alert List
FM Line Console
Station computer (SIPLACE
OIB Display Service)
Orange = Due
Red = Overdue/Defective
Communicate defect
symptom
Faster defect analysis
Better repair results
What caused the error?
Last maintenance date for the
feeder?
What was the last error
indication for the feeder?
What part was last repaired?
Feeder Details
Feeder Maintenance Details
Feeder Defect History
Analyze defect (with help
of history)
Easier analysis of error
symptom
Try another repair
method
What is the defective percentage
of the feeders annually?
For how long are the feeders at
an average in the repair area?
Feeder Maintenance Defect
Summary Report
Planning of repair
resources
Planning amount of spare
feeders
Which feeders (individuals,
types) are extremely often in the
repair area?
Feeder Maintenance Defect
Report
Identify feeders with
repeatable defects
Sort these feeders out in
order to improve line
uptime
Send these feeders for
external repair or scrap
them
Which feeder spare parts are
exchanged and how often?
Feeder Maintenance Defect
Report
Plan spare parts stock
Reduce repair time by
good spares availability
Which feeders were sent for
external repair / 1:1 exchange?
Feeder Exchange Summary
Report
Control feeder inventory
including externally sent
feeders
SIPLACE Feeder Manager 3.3 (R18-1) / Getting Started 08/2018 Edition
148
How long does this procedure
last?
No asset losses
What is the purpose of Feeder
Exchanged Workflow?
The Feeder Exchanged
workflow is being design to
cover the situation whereby
there is a 1 to 1 physical
feeder exchange/replaced
when sending in to repair.
The aim of this function is to
allow user the ability to track
the life span and history of
each individual feeder.
User would know which one
is the replacement feeder,
when it is being replaced
and how long it is being in
used.
Figure 15-4: Example of Use Repair
SIPLACE Feeder Manager 3.3 (R18-1) / Getting Started 08/2018 Edition
149
16 Restrictions
16.1 Feeder Manager and Setup Center coexistence
Feeder Manager can work either with or without Setup Center.
If Feeder Manager Line Console and Setup Center GUI are installed on the same computer,
Feeder Manager will receive feeder and table events forwarded by Setup Center via OIB.
In this case,
a) If the version of Setup Center is equal to or below 5.x, Setup Center will only forward
the feeder events of those feeders that are inside the target setup. Therefore the group
of feeders that can be tracked by Feeder Manager will be limited within the setup
verification context.
b) If the version of Setup Center is 6.0 or higher, then Feeder Manager’s tracking of
feeders is not restricted to the Setup Center verification context.
If the user uses unforced verification mode, and manually restarts the Feeder Manager Line
Console Service, then Feeder Manager Line Console will stop receiving any feeder or table
event. To restore the event and tracking function, the user needs to restart Setup Center, so
that the necessary events can be fired again.
If Feeder Manager detects no Setup Center GUI on the same computer, it will attempt to
subscribe to the necessary events by communicating with the stations (online) and docking
stations (offline) directly.
Feeder Manager only functions with Setup Center whose versions are supported by
OIB.