00196625-03_AI_SX12_PCB_Barcode_de_en.pdf - 第105页
Introduction Conventions for the Use of Safety Instructions Safety Instructions PCB Barcode LP-Barcode 105 1I n t r o d u c t i o n This Assembly Instruction is designed to he lp you in stall the 1 D PCB barcode scanner …
Anhang
Allgemeines zum Barcode Aufbau 2D-Barcodes
104 PCB Barcode LP-Barcode
Introduction
Conventions for the Use of Safety Instructions Safety Instructions
PCB Barcode LP-Barcode 105
1Introduction
This Assembly Instruction is designed to help you install the 1D PCB barcode scanner DS1500 from Da-
talogic and the 2D PCB barcode scanner DataMan 100 from Cognex at SX1/SX2 and SX1/SX2 V2 ma-
chines.
This manual describes how to install the following options on dual conveyors:
▪ PCB barcode scanner 1D SX machine (Datalogic) [00519880-xx]
▪ PCB barcode scanner 2D X/SX machine (Cognex DataMan) [00519881-xx].
Installation on a single conveyor follows the same procedure.
1.1 Safety Instructions
1.1.1 Conventions for the Use of Safety Instructions
This manual contains notes that must be observed to guarantee your personal safety and to avoid dam-
age to equipment. These notes are highlighted by warning triangles and are indicated as follows accord-
ing to the level of risk:
DANGER
Nonobservance of these safety instructions may cause injury to personnel and damage to the
machine!
► Please observe the safety instructions in the user manual of the relevant machine for all
work!
DANGER
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam-
age to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam-
age to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this manual, this indicates that minor injuries or damage to property may
occur if this caution is not observed.
NOTICE
Definition
For the purposes of this manual, this note provides information about the product or indicates
a part of the manual that requires particular attention.
Introduction
Safety Instructions Safety Instructions for the Power Supply
106 PCB Barcode LP-Barcode
1.1.2 Safety Instructions for the Power Supply
▪ This means that some parts of the system carry potentially lethal voltages - even when switched off
at the main power switch.
▪ Incorrect handling of the placement system can therefore result in fatal injuries, severe injuries or
considerable damage to equipment.
▪ Measurements and maintenance work must always be carried out by appropriately qualified person-
nel.
▪ Always follow the applicable accident prevention and DIN regulations (particularly DIN EN 60 204,
part 1) or the regulations specific to your country.
▪ Before starting any maintenance work, switch off at the main switch and disconnect the machine
from the main power supply.
▪ Always secure the machine against unauthorized reactivation. If these instructions are not followed,
you may be able to touch live parts, which could result in fatal or severe injuries.
Maintaining or replacing assemblies
► End all placement operations on the machine.
► Shut down the Windows operating system correctly, otherwise problems may occur when restarting
or data may be lost.
► Switch the machine off at the main switch.
► Disconnect the machine from the main power supply.
► Switch off the machine and attach warnings signs to indicate that service work is in progress.
1.1.3 Safety Instructions for the Gantry
WARNING
Hazardous Voltages!
The machine is supplied with 3 x 400 V~ (or 3 x 204 V~ / 3 x 230 V~ / 3 x 380 V~ / 3 x 415 V~)
± 5 %, 50/60 Hz mains voltage.
► Observe the safety instructions in the user manual during all service work!
CAUTION
Moving the gantry can damage the placement head.
When moving the gantry, observe the following:
► NEVER move the gantry by pushing with your hands against the placement head.
► NEVER push the gantry while the Z axis is lowered.