00196625-03_AI_SX12_PCB_Barcode_de_en.pdf - 第155页
Setting up and Commissioning Connecting the Barcode Scanner to the SIPLACE SX Installing the PCB Barcode Scanner PCB Barcode LP-Barcode 155 3.2.7.2 Connecting the 2D PCB Barcode Scanner Example: connection of 2D PCB barc…
Setting up and Commissioning
Installing the PCB Barcode Scanner Connecting the Barcode Scanner to the SIPLACE SX
154 PCB Barcode LP-Barcode
► Run the cable under the conveyor side and through the cable duct to the box PC (2 to 4). Make sure
that the cable is not in the hazard area of the gantry.
► Use cable ties to fix the cable to the other cables already present.
► Connect the cable to the unoccupied USB port on the box PC (5).
► Fit the cover on the cable duct (6).
See also
3.3.2.1.1 Installing the Barcode Scanner Software [ ➙ 177]
Setting up and Commissioning
Connecting the Barcode Scanner to the SIPLACE SX Installing the PCB Barcode Scanner
PCB Barcode LP-Barcode 155
3.2.7.2 Connecting the 2D PCB Barcode Scanner
Example: connection of 2D PCB barcode scanner to lane 1, top
Legend
► Connect each barcode scanner according to the wiring plan on the option board:
You can use the diagram on the inside of the conveyor control cover for help.
► Run the connection cable to the USB hub (0307 7944-W3) out of the conveyor control tray, at the
back left.
1 Connection X82 2 Connection X84
Conveyor lane Connections on relevant option board
Conveyor lane 1 top X82 and X84
Conveyor lane 2 top X82 and X84
Conveyor lane 1 bottom X81 and X83
Conveyor lane 2 bottom X81 and X83
WARNING
Handling the cable
Cables may only be connected to or disconnected from the machine when currentless.
The connector encoding informs the conveyor control that a scanner is to be used at the rele-
vant installation position. If the scanner is missing, an error message will be issued.
Please note that scanner cables may only be connected to the option board if the correspond-
ing scanner has been fitted.
Setting up and Commissioning
Installing the PCB Barcode Scanner Connecting the Barcode Scanner to the SIPLACE SX
156 PCB Barcode LP-Barcode
Fitting the cover and hub
Conveyor control 1 and 2 – cover fitted and USB hub fixed
Legend
1. Nib of cover
2. Hook and loop fastening tape
3. USB hub fixed
► Refit the conveyor control cover(s). Fit the nib (1) under the screw and then fix the covers(s) into
place with the screw.
► Fix the USB hub on one of the two conveyor controls with the help of the hook and loop fastening
tape (2) provided.
► Connect the connection cable for the USB hub to connection X9 of the USB hub.
► Connect the relevant USB cable for the installed barcode scanner(s) to the respective USB hub con-
nection.
Connections and conveyor lanes
NOTICE
Assigning the USB connections in the setup tool of the barcode scanner software
During barcode scanner configuration, the setup tool assigns each scanner connected for the
first time a virtual COM port, which is kept for future use. As the setup tool can only ever estab-
lish a connection to one scanner at a time, we recommend that - on initial installation - you con-
nect just one scanner to the USB hub and let the setup tool then allocate a virtual COM port
and COM number to this. See "3.3.2.1.2 Configuring the Barcode Scanner Software" [ ➙ 178].
► Repeat this procedure for all barcode scanners to be connected.
Conveyor lane Connections on the USB hub
Conveyor lane 1 top X85_2 on X2
Conveyor lane 2 top X85_4 on X4
Conveyor lane 1 bottom X85_1 on X1
Conveyor lane 2 bottom X85_3 on X3