CM602all_EJM8AESM_Service Manual.pdf - 第279页
Light Transfer-Head Assembly(3 nozzles) See Section "5-8-1. Feeder Gang Exchange Cart Installation and Removal" 4 Install the feeder change cart. Double-sided tape 240×216 TH-1.7 glass board Enter "0"…
Prepare jigs, feeders and boards. 1 to 10
Re-teach "Head Rotation Center Position." 11
Warm up the machine. 12 to 16 Test run of machine
Teach 45°mounting position. 17 to 23
Teach. Place components. Recognize with
head camera. Specify offset (Auto).
Precision test (Placement accuracy test) (1) 24 to 29 Place components. Recognize with head
camera. Measure placement results.
Check precision (accuracy) (1) 30 to 31 Display the precision data.
Enter mounting position offset. 37 Calculate offset from the precision
data and enter it into "Mount position" of
Machine Parameters manually.
Precision test (Placement accuracy test) (2) 24 to 29 Test after entering the mounting position
offset.
Check precision (accuracy) (1) 30 to 31 Display the precision data.
Cpk displayed on CM602 monitor:
Guidance: 1.8 or more
(Equivalent to Cpk 1.5 or more with Panasonic
tester.)
Teach 90° mounting position.
Prepare jigs, feeders and boards. 32 to 36
Follow the procedures for 45°teaching.
Light Transfer-Head Assembly(3 nozzles)
REMARKSITEM
1
Maintenance Adjustment
Flow Chart of Mounting Position Teaching
EJM8A-E-SMA040307-A01-00
Page 4-3-7-2
Light Transfer-Head Assembly(3 nozzles)
See Section "5-8-1.
Feeder Gang Exchange
Cart Installation and
Removal"
4
Install the feeder change cart.
Double-sided tape
240×216 TH-1.7 glass
board
Enter "0" into the mounting position offset.
Maintenance Adjustment
3
REMARKS
Place double-sided transparent tape on the glass board
.
2
ITEM
80101122143164185
66
87
108
129
150
0
90
0
0
-90
180
90
0
-90
180
0
90
0
0
90
-90
180
0
-90
180
0
90
0
0
90
-90
180
0
-90
180
Place narrow double-sided tape.
If the viscosity of the tape is
excessively high, a glass chip
may be broken when removed.
Origin
QFP jig
EJM8A-E-SMA040307-A01-00
Page 4-3-7-3
feeder table, tightening the black screws.
Td4Z4C-a-SHA :Type A High-speed head shadow teaching
Td4Z4C-a-DIR :Type A High-speed head direct teaching
Td4Z4C-b-45D : Type B Multi-purpose head 45°teaching
Td4Z4C-b-90D : Type B Multi-purpose head 90°teaching
Td4Z4C-c-S45
: Type C High-speed shadow teaching, Multi-purpose head 45°teachin
g
Td4Z4C-c-D90
: Type C High-speed direct teaching, Multi-purpose head 90°teaching
* Type A: High-speed heads at Stages A and B
* Type B: Multi-purpose heads at Stages A and B
* Type C: High-speed head at Stage A, Multi-purpose head at Stage B
* To prevent the glass QFP jigs from
being damaged when discharged into
the NG box.
6
7
8
Place cloth in the NG box.
Data type
Load data.
REMARKS
Maintenance Adjustment
5
front and rear stages. Fix the jigs on the
Clean the QFP jigs. Place
them onto Nos. 4 to 18 of
the QFP-jig supplying jig.
Remove the feeder cover.
Place the QFP-jig supplying jig on the
Light Transfer-Head Assembly(3 nozzles)
ITEM
4 18
Slot 5 Slot 26
FrontRear
EJM8A-E-SMA040307-A01-00
Page 4-3-7-4