VI User Manual.pdf - 第363页

Reparation Vision 2007 4.10 User Manua l Rev 01 14 - 11 14.3.4 Operator analysis If after analysis of the reported error s, you judge that error s are not of the good type or that elements not appear ing in error have de…

Reparation

14 - 10 Vision 2007 4.10 User Manual Rev 01

K Defect status in the repair station (NOT REPAIRED, REPAIRED, GOOD).

L Repair inspection result (Operator analysis) (in ConfigReparation.ini file: Enable

operator analysis (0:1)=1).

M No information.

N List of the comments to be link to the defect.

O List of faults as identified by the inspection system for this component.

14.3.2.2 Board representation

You can see the graphic representation or the real picture of the

board. If you have a .bmp file of the board (taken with a scan-

ner), you can display it on this screen (see § 14.3.5.2 Display

real images).

All the faulty components appear in RED in the graphic repre-

sentation. Once a component has been repaired, it is in BLUE.

The actual component to repair is marked by the intersection of

2 lines. You can access to each fault by clicking on any compo-

nent.

14.3.2.3 Defect location

On this part you have the precise location of the defect. The actual

component to repair is marked by the intersection of 2 lines and it

is in RED. This part allows you to zoom in and out to see the pre-

cise location of the component on the board.

For SO and QFP components, the precise positions of solder joints

defects and bridges are displaying.

14.3.2.4 Defect picture

During the vision inspection, the camera can save images of the

defects (max. 30 images are saved).

During the reparation, you will have the picture of the defects.

14.3.3 Repairing faults

If you have gone through all the reported faults, but have not acknowledged repairing or at-

tending to all the faults, you will get this message: The whole panel is done. Some com-

ponents are still on fault. Another turn ?

Click YES to return to repairing the faults on this board or click No if you do not want to return

to repairing the faults on this board.

When all the faults have been attended to, you will be advised by this message: All compo-

nents are repaired. Click OK to continue.

Then, after clicking Alt+F4, you accede to the main menu. Here, by clicking Open in Pro-

duction menu, you can take you back to the repair station main screen and load a new .tst

file to repair.

Use the mouse right click to zoom out and the mouse

left click to zoom in.

Reparation use

Reparation

Vision 2007 4.10 User Manual Rev 01 14 - 11

14.3.4 Operator analysis

If after analysis of the reported errors, you judge that errors are not of the good type or that

elements not appearing in error have defects, you can change the type of errors.

Access to this option while putting in the ConfigReparation.ini the parameter Enable oper-

ator analysis (0:1)=1.

Then several actions are necessary:

1. Launch the reparation: the Repair details screen appears. You can analyze and visualize

each component while clicking above.

In the COMPONENT part, the Repair State information (NOT REPAIRED) is displayed.

At the bottom, the type of errors is displayed.

2. Click on Ctrl + A.

The Find a component window appears.

You must define the Topology and the Board

of the element which you wish to analyze.

Click on OK button.

3. The Error setting window of

the analyzed element ap-

pears. You can see the type

of Error (A) and the Repair

state (B): Not repaired.

Reparation use

Reparation

14 - 12 Vision 2007 4.10 User Manual Rev 01

Tick another or several Error

(A).

Fill in the Reparation part:

 Repair state (Not repaired,

Repaired, Good) (B)

 Error comment (C)

 Operator comment (D).

Click on OK button.

4. The Repair details screen appears. The analyzed element is updated according to the

modifications realized at Step 3.

In the COMPONENT part two fields are filled:

Comment (A)

Repair Button (Operator analysis) (B).

The Repair State information corresponds to the selection in the Error setting window.

At the bottom, the type of errors selected in the Error setting window are displayed.

Reparation use