00198320-02_UM_ShuttleExtension-DE-EN-ZH.pdf - 第135页
Assembly and Instruction Manual 3 Assembly on the SIPLACE TX Shuttle Extension Edition 11/2018 3.1 Scope of delivery 37 3 Assembly on the SIPLACE TX 3.1 Scope of delivery – Shuttle extension: Item no.: 588508 -xx – Trans…
2 Operational safety Assembly and Instruction Manual
2.5 ESD guidelines Shuttle Extension Edition 11/2018
36
2.5.3 Handling ESD modules
Do not touch electronic modules unless it is absolutely essential to do so in order to carry out other
work. If it is necessary, make sure that you do not touch the pins or printed conductors when you
pick up flat modules.
Do not touch components unless
you are constantly earthed by an ESD wrist strap or
you are wearing ESD shoes or ESD shoe earthing strips on an ESD floor.
Always discharge yourself before you touch an electronic module. To do this, simply touch a con
-
ductive and earthed object immediately before you touch the module (such as unpainted parts of
a switch cabinet, a water pipe, etc.).
Do not allow modules with chargeable and highly insulating materials to touch one another, e.g.
plastic films, insulating table surfaces or items of clothing made from synthetic fibers.
Always place the modules on a conductive surface (table with an ESD coating, conductive ESD
foam, ESD bag or container).
Do not move the assemblies near to data view devices, monitors or television units. Keep a min
-
imum distance of > 10 cm to monitors.
2.5.4 Measurements and modifications to ESD modules
Do not take measurements on the modules unless the following conditions are fulfilled:
– the measuring device is earthed (e.g. via PE conductors) or
– you discharge the measuring head just before taking measurements with a potential-free
measuring device (e.g. by touching an unpainted metal part of the controller casing).
Always use an earthed soldering iron if you carry out any soldering work.
2.5.5 Dispatching ESD modules
Always store modules and components in conductive packaging (e.g. metallized plastic bags
or metal sleeves) and dispatch them in conductive packaging.
If the packaging is not conductive, place the modules in a conductive envelope before pack
-
aging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for
example. NEVER use plastic bags or film. 2
If the module has integral batteries, ensure that the conductive packaging does not touch or
short-circuit the battery terminals and, if necessary, first cover the terminals with insulating
tape or material.
Assembly and Instruction Manual 3 Assembly on the SIPLACE TX
Shuttle Extension Edition 11/2018 3.1 Scope of delivery
37
3 Assembly on the SIPLACE TX
3.1 Scope of delivery
– Shuttle extension: Item no.:588508-xx
– Transport rail position 281
– Assembly kit for mechanical connection: Item no.:
– Shuttle extension - holder output conveyor back and front Item no.: 03148418-xx
– Shuttle extension - holder input conveyor back and front Item no.: 03148410-xx
– 2 x SMEMA Cable - for one shuttle extension: Item no.:03152800-xx
– One SMEMA cable for each lane.
– 1 x CAN Bus cable for one shuttle extension: Item no.:03133551-xx
– 1 x Power interface cable to SIPLACE TX: Item no. 03123550-xx
3 Assembly on the SIPLACE TX Assembly and Instruction Manual
3.2 Overview Shuttle Extension Edition 11/2018
38
3.2 Overview
Fig. 3.2 - 1 Mounting interfaces between SIPLACE TX & shuttle extension
Fig. 3.2 - 2 Mounting holes position on SIPLACE TX machine frame (input side)
9
5
0
m
m
±
2
5
Siplace TX Input
Siplace TX Output
Interface
Bracket
Interface
Bracket
without sensor: 7.5mm – 10.5mm
with sensor: 10.5mm – 11mm
without sensor: 7.5mm – 10.5mm
with sensor: 10.5mm – 11mm