SL940-Install-Ops-Maintenance-7210918_B.pdf - 第204页

在线预览 SL940-Install-Ops-Maintenance-7210918_B.pdf PDF 文档。

Glossary G-5

Service Shutdown: When all dispensing is stopped and

the coating system is made safe so that servicing can be

performed.

Service Technician: Trained personnel responsible for

performing advanced system servicing procedures.

SMEMA: Surface Mount Equipment Manufacturers

Association. Established protocol for signal

communication between two or more different systems.

Stop Pin (SL-940E): The Stop Pin is a pneumatic

device used to stop workpieces as they are conveyed

into the system.

SVGA: Super Video Graphics Array. A video card that

produces high-quality color images at high resolution.

TFT: Thin Film Transistor. The Monitor component

that provides color images for a liquid crystal display.

Tool Offset: The tool offset is the X, Y, and Z distance

from the robot's lower tooling pin to the tool tip (the end

of the nozzle). Robot position is calculated using the

coordinates of the tooling pin plus the offset.

Tool: A tool generally consists of a coating applicator

and nozzle. It may also be a teach camera, or a laser

pointer for programming.

Tooling Rails (SL-941E): The adjustable Tooling Rails

secure the workpiece for batch system operation.

Upstream/Downstream SMEMA Sensors: Mounted

on a bracket attached to the conveyor rail, upstream and

downstream SMEMA sensors allow you to manually

load and unload workpieces onto the conveyor in the

absence of upstream or downstream systems.

UV-Cure: Curing method that uses ultra-violet light to

cure (harden) coating materials.

V: Abbreviation for volt as in VAC (Volts Alternating

Current). See also AC, DC.

Valve: See Coating Applicators.

Viscosity: Viscosity is a measurement of the flow

properties of a fluid. The ability of a fluid to resist

deformation under stress. High viscosity fluids have a

high resistance to flow, and low viscosity fluids have a

low resistance.

Water Trap: Moisture from the outside air can

condense in the pneumatic system. The Water Trap

collects this condensed moisture. The Water Trap must

be emptied when it’s full.

Workcell: Dispensing area.

Workpiece: The board or substrate (PCB, PWA, etc.) or

a carrier (pallet, auer boat, lead frame, etc.) to be

dispensed upon.

X-Axis: Left to right movement of the Dispensing Head

in the dispensing area (Workcell).

X-Beam: The apparatus that spans the width of the

dispensing chamber. The Dispensing Head is mounted

to the X-Beam and slides along it in the X-Axis.

Includes mechanical pulleys for the X-Axis cables.

Y-Axis: Forward and backward movement of the

Dispensing Head in the dispensing area (Workcell).

Z-Axis: Up and down movement of the Dispensing

Head in the dispensing area (Workcell).

Index I-1

Index

Adjustable Tooling Rails ............................................ 1-4

Air Pressure

adjusting conveyor air pressure ........................... 5-13

adjusting fluid air pressure ................................... 5-10

adjusting main air pressure .................................... 5-8

adjusting reservoir air pressure .............................. 5-9

Applicator ON/OFF Button ...................................... 1-12

Bar Code Scanner

configuration ........................................................ 6-18

testing .................................................................. 4-20

utilities ................................................................. 4-20

Bar Code/Data Matrix Reader .................................... 1-4

Board Pins ................................................................ 1-14

Board Present Sensor ................................................. 1-4

Board Sensor ............................................................ 1-14

Brush Box .................................................................. 1-4

Cables

tension reminder .................................................. 7-12

tensioning ................................................... 7-12–7-13

Camera

configuration .......................................................... 6-5

installation ........................................................... 3-10

states ...................................................................... 4-6

Characterization ....................................................... 6-18

Characterization Sheet .............................................. 6-20

Circulating Heated Fluid System ............................. 1-18

Coating Applicators........................................... 1-8, 1-13

SC-104HS/SC-105HS............................................ 1-8

SC-105VCS ........................................................... 1-8

SC-204HS/SC-205HS............................................ 1-8

SC-300 ................................................................... 1-9

SC-400 ................................................................... 1-9

Coating Area ............................................................ 1-11

Coating Process .......................................................... 5-4

Coating System

anchoring ............................................................. 3-10

configuration and characterization ......................... 6-1

detailed operation .................................................. 5-4

dispensing area .................................................... 1-11

facility requirements ............................................ 10-1

front panel ............................................................ 1-12

installation ............................................................. 3-1

levelers ................................................................. 1-11

leveling .................................................................. 3-6

lower front cabinet ...............................................

1-15

maintenance ..................................... See Maintenance

manuals supplied ................................................... 1-2

optional equipment ................................................ 1-4

safety ..................................................................... 2-1

shutdown.............................................................. 5-15

standard equipment ................................................ 1-3

startup ........................................................... 4-5, 5-14

system description ................................................. 1-1

system features .................................................... 1-10

testing .................................................................... 4-8

warranty ................................................................. 9-2

Computer .................................................................... 1-3

installation ............................................................. 3-9

Configuration

bar code scanner .................................................. 6-18

beacon .................................................................... 6-6

conveyor .............................................................. 6-13

fan width control .................................................... 6-9

fixture .................................................................. 6-10

inverter ................................................................. 6-15

reconfigure ............................................................. 6-2

robot ............................................................ 6-16, 6-17

setting fixture constraint location ........................ 6-10

tool ......................................................................... 6-8

Conformal Coating

characterization .................................................... 6-18

curing ..................................................................... 5-1

defined ................................................................... 5-1

Connecting the Power and Air Supply ....................... 4-3

Conveyor ........................................................... 1-3, 1-14

adjustments ............................................................ 5-3

chain ............................................................... 1-3, 5-3

chain replacement .................................................. 9-5

configuration ........................................................ 6-13

manual width adjustment ..................................... 1-14

tensioning chains ................................................. 7-14

testing .................................................................. 4-10

troubleshooting ...................................................... 8-3

utilities ................................................................. 4-18

Conveyor Air Regulator and Gauge ......................... 5-13

Daily Routine Procedures ......................................... 5-17

Database Utility ........................................................ 5-28

Dispensing Head ............................................. See Robot

Disposal

equipment .............................................................. 2-4

materials ................................................................ 2-4

Dual Toggle Mounting Bracket .................................. 1-5

Dual-Simultaneous Mounting Bracket ....................... 1-5

Earthquake Precautions .............................................. 2-5

Easy Coat for Windows XP............................. See ECXP

ECW.INI .................................................................... 6-2

ECXP .................................................................. 1-3, 5-2

bar code scanner utilities ..................................... 4-20

characterization wizard ........................................ 6-22

configuration .......................................................... 6-2