SL940-Install-Ops-Maintenance-7210918_B.pdf - 第40页

2-6 Safety 2.9 Safety Warning Labels WARNING! CAUTI ON! Comply with all safety warning labels or serious injury to personnel or dama ge to the coating system may occur. Worn or damaged labels shoul d be replaced with new…

100%1 / 208
Safety 2-5
• Lift your head and shoulders first and with your back straight, use the strength of
your legs to slowly and smoothly raise yourself up.
• DO NOT twist your body. Change direction by first moving your feet.
• When transporting the load on a cart or a lifting device, reduce back strain by
pushing rather than pulling the load.
• When lowering the load, bend your knees, lower it slowly and smoothly, and keep
your fingers out from under the load.
2.7 Laser Radiation
The optional Laser Fan Width Control uses a Class II laser sensor. The following safety precautions
should be observed in addition to the standard coating system safety precautions.
• Operate the Laser Fan Width Control only according to the procedures described in the
instructions included. Failure to do so may result in injury due to exposure to the laser beam.
• DO NOT look directly at the laser beam.
WARNING! Looking directly at the laser beam may result in serious eye injury.
NOTE The laser beam is not harmful to the skin. There is no danger in exposing arms or hands
to the beam. The only possible health hazard is in exposing the eyes to the laser beam.
Table 2-1 Laser Fan Width Control Specifications
ORGANIZATION CLASSIFICATION
FDA CLASS II
IEC 60825-1 1998-01 CLASS 2
DIN EN 60825-1 1998-01 KLASSE 2
2.8 Earthquake Precautions
In the event of an earthquake, your coating system must be secured to prevent movement that could
cause injury to personnel and damage to the coating system and facility. Each coating system leveler
(foot) should be anchored to the floor. See 3.9 Anchoring the Coating System.
As a safety precaution, all hazardous electrical and pneumatic energy is automatically bled out of the
system if electrical power is lost.
WARNING! All personnel should follow facility earthquake safety guidelines.
2-6 Safety
2.9 Safety Warning Labels
WARNING! CAUTION!
Comply with all safety warning labels or serious injury to personnel or damage to
the coating system may occur. Worn or damaged labels should be replaced with
new labels having the same part number.
Warning labels on your Select Coat SL-940E/SL-941E point out areas where personnel must use extreme
caution to prevent serious injury and property damage. Table 2-2 shows the warning symbols that may be
found on your coating system or optional equipment. The location of warning labels found on a typical
SL-940E/SL-941E is shown in Figure 2-2 and Figure 2-4.
Table 2-2 Safety Warning Symbols
Warning Type Symbol
Part
Number
Hazard
Consult
Operator’s
Manual
7206854
Warns personnel to read Operator’s Manual before
operating machine.
Electrical
(Shock Hazard)
70-0116-00
(1)
or
70-0050-00
(2)
This label warns of a high-voltage component that can
cause shock, burn, or death. Use extreme caution
when working in or around these areas. Disconnect
and lock out power before servicing.
General
Warning
70-0055-00
This label identifies a component that requires special
attention. Can cause serious bodily harm to the user.
Hand
Entanglement/
Moving
Material
7214364
(1)
This label warns of moving parts that can cause
serious injury to hands and fingers.
Disconnect and lock out power before servicing.
Heavy Object
(Lifting Hazard)
70-0118-00
(1)
or
196666
(2)
This label warns that the labeled component is heavy
and can cause muscle strain or back injury to
personnel trying to lift it.
Hot Surface
70-0121-00
(1)
or
70-2150-00
(2)
Thermal warning labels identify potentially hot
components and surfaces. Use extreme caution when
working on or around these areas. Can cause severe
burns.
Laser Radiation
Warning
7206858
(2)
This label warns of the possibility of hazardous
radiation exposure.
Moving Parts
Present
70-0120-00
(1)
or
198883
(2)
This label warns of moving parts that can cause
serious injury to hands or fingers. Keep hands away
from moving parts. Disconnect and lock out power
before servicing.
Pressure Relief
Warning
322352
This label warns that the pressure relief valve should
be pulled before performing service on the pneumatic
system or opening the fluid reservoir.
Notes: (1) Rectangular labels with symbols and text. These labels are placed on machines that are shipped anywhere but the
European community.
(2) Triangular labels with symbols only. These labels are placed on machines that are shipped to the European
community, referred to as “CE labeled” machines.
Safety 2-7
Item Description
1 Read Manual Label (Front Hood)
Figure 2-1 Safety Warning Labels - Front View
Item Description
1 Laser Radiation Warning Label
Figure 2-2 Safety Warning Labels - Laser Fan Width Control
1
1
1