编带机说明书-含图纸ttm402.pdf - 第156页
6-12 TM-403 User’s Guide Preparing to Ru n a Pre-programmed Job D292105.8b.fm
D292105.8b.fm Preparing to Run a Pre-programmed Job
Chapter 6: Operation 6- 11
Run the Job
1. Close the enclosure doors, then open the HMI Run Tab and press Run.
During operation, the operator will add additional parts to the Bowl Feeder and
unload packaged parts from the Taper as necessary. The operator may also
replace parts that fail 2D Inspection. Otherwise no other adjustments are required
for a job that has already been defined properly.
2. When the preset number of parts has been run, the TM-402 will automatically stop
operation.
Note: If Leader has been ENABLED, the Taper will continue to seal tape until it
reaches the programmed Leader length. If Leader is DISABLED, the Taper will
continue to seal tape until the last sealed part has reached the cut point.
3. Cut the sealed tape at the cut point and use a piece of blue Permacel tape to
secure the finished reel. Remove processed output.
Step 8:
Run
Job
6-12 TM-403 User’s Guide
Preparing to Run a Pre-programmed Job D292105.8b.fm
Chapter 7: Troubleshooting
Contents
Emergency Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
Activating an Emergency Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Clearing an Emergency Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
System Alarm Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-6
Error Message Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
Adjusting Nozzle Vacuum Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-23
Tips on Part Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-24
Sensor Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-27
Adjusting the Low Cover Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
Adjusting the Tape Jam Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
Adjusting Heat Seal Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-28
Heat Seal Shoe Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28
Seal Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29
Sealer Dwell Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29
Adjusting PSA Seal Quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-30
Materials Used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30
Seal Roller Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30