编带机说明书-含图纸ttm402.pdf - 第80页

4-8 TM-403 User’s Guide Nozzle Installation D292105.7b.fm Installing Nozzle & Nozzle Tip 1. Move the Pick & Place Head to the Place position so it is easily accessible from the front. . 2. Remove the air line fro…

D292105.7b.fm Nozzle Installation

Chapter 4: Setup 4- 7

Nozzle Installation

The TM-402’s is shipped with the following nozzles and nozzle tips:

• (1) Quad Nozzle Shank (Part # 267090)

• (1) Small Precision Tool (SPT) Nozzle Shank (Part # 267091)

• (1) Convum Nozzle Shank (Part # 267008)

• (1) Large Quad Vacuum Cup (Part # 201297)

• (1) Medium Quad Vacuum Cup (Part # 201298)

• (1) Small Quad Vacuum Cup (Part # 201299)

• (1) SPT Vacuum Cup (Part # 201271)

• (1) Convum Vacuum Cup (Part # 201207)

• (2) Nozzle O-Rings (Part # 212025)

Note: Nozzle Tips are available in a wide range of sizes and style. See the Sug-

gested Spare Parts List in the back of this User’s Guide for more details. Contact

V-TEK Service for information on ordering additional Nozzle Tips.

Selecting the Correct Nozzle & Nozzle Tip

To achieve the best picking results, select the largest cup size the part can accommo-

date. Maximizing the cup size gives the vacuum access to more surface area which

increases its pick-up capability. The goal is to use a nozzle cup that is just slightly smaller

than the part being picked.

The Convum bellows-style cups have a flexible flange that are useful for picking irregular

or heavy parts.

Step 4:

Nozzle

Installation

SELECT

NOZZLE

Convum Quad SPT

4-8 TM-403 User’s Guide

Nozzle Installation D292105.7b.fm

Installing Nozzle & Nozzle Tip

1. Move the Pick & Place Head to the Place position

so it is easily accessible from the front. .

2. Remove the air line from the Nozzle Shank, sup-

porting the Nozzle with one hand while gently pull-

ing the tube off the Nozzle Barb.

3. Using a 2mm Hex wrench, loosen the set screw

that retains the Nozzle Shaft.

4. Slide the Nozzle Shank down and remove it from

the Pick & Place Assembly. Store the unused

Nozzle Shank and Nozzle Cup in the Spare Parts

Kit.

5. Select the correct Nozzle Shank and Nozzle Cup

for the part that will be run. Press the Nozzle Cup

onto the Nozzle Shaft.

6. Insert the Nozzle Shank into the Actuator Shaft in

the Pick & Place Assembly.

Note: When positioning the Nozzle Shank,

push it all the way up to the Actuator Shaft,

then pull it back slightly (about 1mm) so the

body of the Nozzle Shank doesn’t rub the body

of the Actuator.

7. Using a 2mm Hex wrench, tighten the set screw to

retain the Nozzle Shaft..

8. Re-attach the air line to the Nozzle Barb.

Step 4:

Nozzle

Installation

INSTALL

NOZZLE

D292105.7b.fm Taper Setup

Chapter 4: Setup 4- 9

Ta p e r S e t u p

Loading Tape

The Taper must be loaded with carrier and cover tapes and configured for operation.

Begin by preparing the Taper, then move to the HMI to adjust settings. (Step 7)

Load Carrier Tape

1. Check that the taper is set at the correct width for the carrier tape. If not, push or

pull the outer track in or out as needed, sliding it on the Detent Shafts until it is at

the required width.

3. Once the track is adjusted, use a strip of the carrier tape as a test to determine if

the setting is correct. The carrier tape should slide through freely, but without

excess play back and forth. Tighten the set screws down again to secure the track

into place.

Step 5:

Setup

Ta p e r

Step 5:

Setup

Ta p e r

CARRIER

TA P E

Detent Shaft

Outer Track