00194440-10_SM_X-Series_Customer_en.pdf - 第142页
Service Work C&P20 Nozzle Changer 3.5.1 Replacing the Nozzle Changer 142 Service Manua l SIPLACE X Series 3.5 3 . 5 C & P 2 0 N o z z le C h a n g e r C&P20 Nozzle Changer Overview 3.5.1 3 . 5 . 1 R e p la c …
Service Work
3.4.7 Replacing Stationary Component Camera Digital Type 25/33/36 Placement heads
Service Manual SIPLACE X Series 141
3.4.7.1
3.4.7.1 Installation Height of the Stationary Camera
Installation Height of the Stationary Camera
The installation height at which the camera can be installed depends on the camera version. You will
either only be able to use one specific height or will have the option of several installation heights. The
following description only applies for the following camera versions with three possible installation
heights:
▪ Stationary component camera P&P (type 33) 55x45 digit. [03016339-xx] from version -06
▪ Stationary component camera P&P (type 36) 32x32 digit. [03042491-xx] from version -04
Stationary Camera in Position 1
Stationary Camera in Position 2
Position 2 is not relevant for the SX and the X series.
Stationary Camera in Position 3
CAUTION
Head crash danger
An incorrect installation height can result in a head crash!
1. Screw
2. Thread in the machine frame
Position 1 has to be used in the following cases:
▪ SX1/SX2: always
▪ SX4, X series: If at least one DLM or CPP head is
used in the corresponding placement area.
1. Screw
2. Thread in the machine frame
Position 3 has to be used in the following cases:
▪ SX1/SX2: never.
▪ SX4, X series: If only TwinHeads are used in the cor-
responding placement area.
Service Work
C&P20 Nozzle Changer 3.5.1 Replacing the Nozzle Changer
142 Service Manual SIPLACE X Series
3.5
3.5 C&P20 Nozzle Changer
C&P20 Nozzle Changer
Overview
3.5.1
3.5.1 Replacing the Nozzle Changer
Replacing the Nozzle Changer
Overview
1. Cover (covering complete electronic and pneumatic
systems)
2. Toggle (six of them)
3. Nozzle magazine
4. Fastening screws
1. Cover (two x four fastening screws)
2. 1 wire board (NC control board)
3. Valve assembly
4. Swivel drive
5. Microswitch (six of them)
6. Green LED three mm
4
1
4
3
2
5
1
6
5
4
3
2
1. Cover (covering complete electronic and pneumatic
systems)
2. Connection plug
3. Compressed air connection
4. Fastening screws
4
1
4
3
2
Service Work
3.5.1 Replacing the Nozzle Changer C&P20 Nozzle Changer
Service Manual SIPLACE X Series 143
Removal
Installation
► Unplug the nozzle changer connection plug (2).
► Disconnect the hose (3) from the pneumatic coupling.
► Loosen the four fastening screws (4) and carefully lift
the nozzle changer out of the machine.
Pay attention to the support plates. Remember their
exact positions, as they will need to be returned to
these original positions, during assembly.
4
1
4
3
2
NOTICE
Fitting the nozzle changer
When fitting the nozzle changer, make sure that the component reject tray can be removed.
Make sure that the screws you are using are not too long, as these might jam the reject tray.
► Fit the new nozzle changer with the support plates.
► Reconnect to the electrical and compressed air sys-
tems.
► Check the mechanical height of the nozzle changer
(see Setting the Nozzle Changer Height).
4
1
4
3
2