00194440-10_SM_X-Series_Customer_en.pdf - 第222页

Service Work Cutter 3.9.7 Replacing the Cutter Blades 222 Service Manua l SIPLACE X Series Removal ► Remove the cutter from t he machin e. For det ails, read the relevant section o f this instruction manual. ► Loosen the…

100%1 / 384
Service Work
3.9.7 Replacing the Cutter Blades Cutter
Service Manual SIPLACE X Series 221
3.9.7
3.9.7 Replacing the Cutter Blades
Replacing the Cutter Blades
Parts, equipment and tools
Select the right set of blades.
We recommend the following additional spare parts:
▪ 2x blade cover (cutter HF) [03000553-xx] (cover for screws of movable blades)
▪ 2x ISO4762-M5x35-12.9, geomet 321+VL [03057290-xx] (screws for movable blades)
▪ 2x articulated joint (cutter HF) [03000518-xx]
▪ 2x DIN71412-BM6 [03036943-xx] (lubrication nipple)
Consumables required:
▪ Lubricant grease Klüber BEM 34-132 tin 1 kg [00374565-xx] (identical to the lubricant grease used
on the guide carriage of the gantry)
▪ Interflon Fin Grease [03020782-xx]
▪ LOCTITE 243 screw locking varnish [00334892-xx]
Tools required
▪ Extra protection gloves, leather [00091001-xx]
▪ Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
▪ Torque wrench 2.5 - 25 Nm [00376625-xx]
▪ Bit holder for TorqueVario screwdriver [03078706-xx]
▪ Socket-head bit size 3-6
▪ Fork wrench, size 10
▪ Feeler gauge
▪ Brush
▪ Cloth
▪ Two large parallel clamps and a sturdy table with even surface, to clamp down the dismantled cutter
CAUTION
Risk of injury!
There is a high risk of injury from the blades and the tape deflector.
► Wear appropriately thick protective gloves!
► Never reach into the cutter from below or into the empty-tape duct from above.
► Make sure that no-one can injure themselves on the cutter after it has been dismantled and
placed next to the machine!
Machine Tape cutter, pneumatic Function status Set of blades
X series, SX4, DX4, X
series S
03066690-xx
(without CAN nodes)
-01 03009259-xx
HF, X series 03000487-xx -01 to -03 03000501-xx
-04 to -05 03009259-xx
X Series 03019941-xx
(with control unit)
-01 03009259-xx
03052900-xx
(with CAN nodes)
-01 to -02 03009259-xx
Service Work
Cutter 3.9.7 Replacing the Cutter Blades
222 Service Manual SIPLACE X Series
Removal
► Remove the cutter from the machine. For details,
read the relevant section of this instruction manual.
► Loosen the screws (2) fastening the top cover
plate (3) and then remove the cover plate.
► Loosen the screws (2) fastening the baffle plate (3) to
the back of the cutter and remove the baffle plate.
► Remove the caps over the fastening screws (1) on
the movable blade and loosen the blade.
CAUTION!
Risk of injury!
There is a risk of injuring yourself on the cutting edge of
the blades.
Cutter (using example of X series)
► Loosen and remove the two screws (1) fastening the
stationary blade (2).
► Loosen the screws fastening the left and right tape
deflectors (3) above the moveable blade.
CAUTION!
Do not loosen all screws!
Do not loosen these two screws (4)
► Remove the tape deflector holder with the tape de-
flector (5) and carefully place the whole unit down
(with the tape deflector facing upwards).
Service Work
3.9.7 Replacing the Cutter Blades Cutter
Service Manual SIPLACE X Series 223
Installation – requirements
▪ Wear appropriately thick protective gloves!
▪ Make sure all parts are clean before installing them.
▪ The new blades are covered with a fine lubrication film.
Do not use fat dissolving agents on the blades (risk of rust film forming).
The blades may only be greased with the lubricants described in the maintenance manual.
Any other lubricant would impair the movement of the moveable blade.
▪ If the new blades are not clean, carefully clean them (wear protective gloves) with a clean brush or
a well folded, clean and dry cloth.
Do not use fat dissolving agents!
Preparation
► Make sure the cutter is in the correct rotary position (see the slant of the blade).
► Check the positioning of the individual blades to one another.
► Before installation, lubricate the sliding side surfaces of the moveable blade with Klüber BEM 34-132
and make sure that the recesses are filled. These will be refilled later on during maintenance with
the lubrication adapter.
Cutter (using example of X series)
► Remove the right-hand holding-down device (1) and
the left holding-down device (2), plus the spacers be-
low.
► Use an SW 10 open-ended wrench to push against
the joint (3), while loosening the hexagon socket-
head screw of the joint (4) in the moveable blade.
This may require more strength than usual as the
screws have been secured with Loctite no. 243.
► Grasp both ends of the moveable blade (5) with the
protective gloves and pull it upwards and out.
CAUTION
Risk of injury!
There is a high risk of injury from the blades and the tape deflector.
1. Stationary blade
2. Moveable blade
3. Sliding surfaces to be lubricated
4. Holding-down device
5. Spacer
6. Contact surface