00194440-10_SM_X-Series_Customer_en.pdf - 第337页
Settings 5.4.6 Board Clamping Functions Conveyor Settings Service Manual SIPLACE X Series 337 Procedure A) Checking the clamping play: ► Move the lifting table upwards, without the bo ard. ► With the aid of a 0.1 mm feel…
Settings
Conveyor Settings 5.4.6 Board Clamping Functions
336 Service Manual SIPLACE X Series
Quad lane conveyor settings
► For initial setting, follow the procedure used for the single and dual conveyors (see above). Make
sure that the long terminal strip [03076698-xx] is fitted on the 94 mm side of the "setting gauge ac-
tuator assembly".
► As two boards are clamped with the same lifting table, you need to check the clamping play for each
of the single conveyors.
► The clamping actuators are delivered with a basic setting of 94.2 mm to the top edge of the conveyor
belt.
► If problems occur during board clamping (board partially or fully loose), you will need to reset the
clamp.
The cause of this problem is that there are a total of six actuators on three conveyor edges. If these
are not set accurately enough (they do not form a level), up to three actuators might have been set
incorrectly. These then need to be adjusted.
(1) Conveyor belt play on the lower edge of the
clamp
(2) Distance 94.2 mm.
Settings
5.4.6 Board Clamping Functions Conveyor Settings
Service Manual SIPLACE X Series 337
Procedure
A) Checking the clamping play:
► Move the lifting table upwards, without the board.
► With the aid of a 0.1 mm feeler gauge, check the gap between the conveyor belt and the clamp (see
graphic above).
If the gap is larger than 0.1 mm, the distance determined between the belt and clamping edge on the
actuator will need to be reset.
To do this, you need to add the current distance between the actuator and the clamping plate to the
distance between the belt and the clamping edge!
► Move the lifting table down again.
B) Setting the play on the actuator:
► Disable the clamp and move the lifting table down.
► Measure the play between the actuator and the side edge with a feeler gauge.
► Loosen the actuator screws.
► Set the distance again with the help of a feeler gauge.
Add the play for the clamp to the play for the actuator.
► Tighten the actuator screws again.
► You now need to recheck the gap between the conveyor belt and the clamp when the lifting table
has moved up. (see above)
► If a problem occurs during board clamping, recheck this setting again. We recommend that you
check this setting every three months. When cleaning the machine, always make sure that you re-
move all components from the conveyor belt.
NOTICE
Play between the terminal strip and the upper edge of the conveyor belt
The play between the terminal strip and the upper edge of the conveyor belt may not be more
than 0.1 mm.
1. Actuator screwed fixtures
2. Measuring the play with the feeler gauge
Settings
Conveyor Settings 5.4.7 Readjusting the Holder for the Stopper and Proximity Switch (QC)
338 Service Manual SIPLACE X Series
5.4.7
5.4.7 Readjusting the Holder for the Stopper and Proximity Switch (QC)
Readjusting the Holder for the Stopper and Proximity Switch (QC)
If the fixture rail for the stopper and proximity switch is loosened or dismantled, this will need to be read-
justed.
Tools
▪ Standard tool
▪ Gauge for Stopper Setting [03067221-xx]
Performing the setting
Position of the conveyor edges with setting gauge.
1. Distance between the conveyor edges for fitting the
setting gauge
► When dismantling the belt guidance, make sure that
the slide is secured.
► Set the conveyor so that the conveyor edges are not
against one another.
Dismantling the clamping and distance rail.
► Loosen the screws (1) and dismantle the clamping
rail and the distance rail of the conveyor edge.