00194440-10_SM_X-Series_Customer_en.pdf - 第326页
Settings Conveyor Settings 5.4.3 Setting the Fixed Conveyor Edge (from SW 701) 326 Service Manua l SIPLACE X Series 5.4.3 5 . 4 . 3 S e t t in g t h e F ix e d C o n v e y o r E d g e ( f r o m S W 7 0 1 ) Setting the Fi…
Settings
5.4.2 Setting the Fixed Conveyor Edge (SW60x) Conveyor Settings
Service Manual SIPLACE X Series 325
► Configure the new conveyor mode in SIPLACE Pro
5.4.2.4
5.4.2.4 Re-converting Single Conveyor Mode
Re-converting Single Conveyor Mode
► In the SITEST conveyor menu Options and Configurations, select the menu Change Widening of
Conveyor to set the default conveyor mode.
► The moveable conveyor side of conveyor 1 (right side fixed (track 1 left side fix)) is moved to a small
conveyor width.
► The SITEST SW ask to disconnect the lifting tables - Do so-.
► The SITEST SW will now use the conveyor control SW to move the fixed side of conveyor 2 (right
side is fixed (lane 1 left side fixed)) back to its standard position. Check the dimensions near the ad-
justment units.
► Now adjust conveyor width of both tracks to desired values.
5.4.2.5
5.4.2.5 Moving the Fixed Conveyor Edge for ’Extra Wide Conveyor’
Moving the Fixed Conveyor Edge for ’Extra Wide Conveyor’
The standard positions of the fixed conveyor edge(s) are defined according to the dimensions of the X4,
X3 and X2 machines. Due to the additional width of HF machines, HF lines with single conveyors can
have up to 508 mm wide boards; dual conveyors up to 250 mm wide boards on each lane.
► Go to the SITEST conveyor menu Options and Configurations and select Extra wide, to set the con-
veyor mode "extra wide".
► The fixed conveyor edge of conveyor 2 (right side fixed (track 1 left side fix)) remains in its position.
► The ’fixed conveyor of track 1(right side fixed (track 2 left side fix)) is moved 34mm outside. This al-
low the wider boards. The moveable side of track 2 (track 1 left side fix) could be set now to more
than 216 mm wide boards.
NOTICE
SITEST
When converting the dual conveyor to a single conveyor (flexible dual conveyor, connect the
lifting tables when requested to do so by SITEST (we recommend doing this without com-
pressed air supply to the lifting table). This function is supported by SIPLACE Pro .
NOTICE
HF, X and D machines
This operating mode is possible for HF, X and D machines with single or dual conveyors.
CAUTION
Measuring and calibrating
After the conversion process, you need to measure/calibrate the board reference corner and
the conveyor edges and then save this information in the machine data.
Settings
Conveyor Settings 5.4.3 Setting the Fixed Conveyor Edge (from SW701)
326 Service Manual SIPLACE X Series
5.4.3
5.4.3 Setting the Fixed Conveyor Edge (from SW701)
Setting the Fixed Conveyor Edge (from SW701)
5.4.3.1
5.4.3.1 General Notes
General Notes
Setting the Fixed Conveyor Edge
The fixed conveyor side is always set in the standard mode with right side fixed. You need to set a value
of 38.8 mm between the conveyor base and the fixed conveyor side, with the help of a gauge.
▪ [03054247-xx] Gauge for fixed conveyor edge DT/ET HS60/D4
▪ [03054248-xx] Gauge for conveyor edge distance DT HS-60/D4
Teach the fixed side with the software and store the value.
Setting the fixed conveyor side
When using dual conveyors in the X4I, the fixed conveyor
side can be set as required i.e. the left or right side, or the
outer edges of each conveyor for i-placement. The com-
patibility to the other machines can be set via predefined
values in the SW (see diagram).
NOTICE!
This menu is accessible from operator level Service (cus-
tomer)!
Settings
5.4.3 Setting the Fixed Conveyor Edge (from SW701) Conveyor Settings
Service Manual SIPLACE X Series 327
Values
The measurement is performed between the side flange and the fitting flange of the mounting frame (see
also the "Example X-Series")
Example of X series
Setting the "fixed conveyor side" in SIPLACE X, HF series
Machine Single conveyor
Standard width
508 (460) mm
Dual conveyor
Standard width
250 (216) mm
Quad lane
Standard width
114 mm
HF series 19 (43) mm 4.5 (38.8) mm
X series / D3
up to July 2007
19 (43) mm 4.5 (38.8) mm
X series / D3
from July 2007
16 (40) mm 4.5 (38.8) mm 2 mm
X4I 16 (40) mm 4.5 (38.8) mm 2 mm
Machine Single conveyor
Standard width
460 mm
Dual conveyor
Standard width
216 mm
HS-60 34.5 mm 30.5 mm
S27 HM 34.5 mm 30.5 mm
D4 34.5 mm 30.5 mm
D1/D2 34.5 mm 30.5mm
NOTICE
Only with SITEST
The fixed conveyor side should be adjusted only with the SITEST software and the width ad-
justment devices. This ensures that the conveyor sides are in their correct positions (parallel)
i.e. that the conveyor runs straight.