YSP20_Users_E.pdf - 第98页
4-6 4 aily operation 3 Set the backup pins (or board support jigs). When the DOOR LOCK lamp turns off, open the safety cover and set the backup jigs on the matrix plate to match the size of the board to be pr oduced. I…
4-5
4
aily operation
4. Changing the conveyor unit setup
When producing boards that are different from the previous production board, you need to change the
conveyor unit setup to match the selected board. (This procedure is not necessary when you are producing
the same board as last time.)
c
1
On the Setup screen, open the [Setup] tab under "Utility".
The buttons on this screen are used in the following steps to change the conveyor unit setup.
Setup screen
[Setup] tab
Step 2:
[SW. Prod. Position] button
Step 5:
[Convey In]
button
64406-N3-10
2
Press the [SW. Prod. Position] button.
Select the setup item.
n
NOTE
When both lanes are used for production, the dialog box for selecting the lane number appears, so select the lane.
The lane currently used in production is grayed out.
1. When rearranging the backup pins, select “Transfer Check Position”. The conveyor will move to the
setup position and the conveyor width will be automatically adjusted to match the board size.
2. When changing the whole matrix plate, select “Backup Setup”. The conveyor will move to the setup
position and the conveyor will be adjusted to the maximum width, allowing you to remove the matrix
plate.
n
NOTE
When removing the matrix plate, check for safety and then lift it straight up while holding firmly with both hands.
Dialog box for move table to setup position
64307-N3-00
4-6
4
aily operation
3
Set the backup pins (or board support jigs).
When the DOOR LOCK lamp turns off, open the safety cover and set the backup jigs on the matrix plate
to match the size of the board to be produced. If using optional board support jigs, they can be used
together with the backup pins.
c
immediately in case of emergency.
OK
NG
Arranging the backup pins
Backup pins
Backup pins
(When board support jigs and backup pins are used together)
Board support jig
Fixed conveyor rail
Board support jig
Machine front side
Matrix plate
Matrix plate
63402-N3-10
n
NOTE
When the backup pin arrangement has been input by pressing the [Backup Pin Pos.] button on the [Print]-[Board] tab
screen, this is convenient to arrange the backup pins. (For more details, see “3. Back pin arrangement” in Chapter 7.)
4
Close the cover and press the [READY] button.
5
Press the [Convey In] button to load a board into the machine.
Follow the instructions that appear on the screen to load a board into the machine. The board is
automatically clamped in the print position.
n
NOTE
When both lanes are used for production, the dialog box for selecting the lane number appears, so select the lane.
The lane currently used in production is grayed out.
6
Check the board clamp status.
1. Press the [SW Prod. Position] button and select “Transfer Check Position”.
2. When the DOOR LOCK lamp turns off, open the cover and touch the board to check for warpage
and backlash.
4-7
4
aily operation
5. Replacing the cleaning gauze roll
If the cleaning gauze roll is wound up completely or if the gauze roll with a different size needs to be used
during the setup work, follow the steps below to replace the cleaning gauze roll.
c
n
Gauze roll part No.
Part No. Part name Notes
KHT-M3660-00X BENCOT,ROLL 530 Roll sheet width, 530 mm
KGY-M3660-A0X BENCOT,ROLL 440 Roll sheet width, 440 mm
KGY-M3660-B0X BENCOT,ROLL 360 Roll sheet width, 360 mm
KGY-M3660-C0X BENCOT,ROLL 260 Roll sheet width, 260 mm
c
Select a gauze roll width that matches the squeegee head size. Using the wrong gauze roll width might damage the
squeegee head and mask.
c
below) under the mask plate.
Cleaning unit
Mask plate
Cleaning unitHandle
63403-N3-00