2OM-1088-002.pdf - 第191页
Tg0699-PM-D2 1. Pattern Program Data Sheets 0207-001 Chapter 1 5-4 Pattern Program Date of Preparation Comment 1 Prepared by Comment 2 Screen Recognition Scr . Recog Function 2PT . Center Recognition OFF/ON Fiducial Mark…
Tg0699-PM-D2
1. Pattern Program Data Sheets
0207-001 Chapter 1 5-3
Pattern Program Date of Preparation
Comment 1 Prepared by
Comment 2
PCB Backup
Chuck Stage Select Backup Jig/Backup Pin/Vacuum Plate
/Vacuum Plate (Clamp Off)
PCB Warpage Protection OFF/ON
Vacuum Release Mode Before/After
Vacuum Rel. Wait Time . seconds
PCB Clamp Offset Timing . seconds
Position +/- . mm
Bef.Clamp Fll Speed/10%Down/20%Down/30%Down/
Bkup Spd. 40%Down/50%Down/ 60%Down/70%Down/
80%
Down/90%Down
Aft.Clamp
Fll Speed/10%Down/20%Down/30%Down/
Bkup Spd. 40%Down/50%Down/ 60%Down/70%Down/
80%
Down/90%Down
PCB Stopper Offset Y +/- . mm
PCB Cut Offset . mm
PEC Recognition
P.E.C. Recog. Function 2PT.
Center Recognition OFF/ON
Fiducial Mark #1 X (Horizontal) . mm
Y (Vertical) . mm
Recog. Mode Mark/Model/Model+Mark
Code
Auto Gain Adj. OFF/ON
Gain
Level
Calib. Lamp Normal/Ring/Both
Fiducial Mark #2 X (Horizontal) . mm
Y (Vertical) . mm
Recog. Mode Mark/Model/Model+Mark
Code
Auto Gain Adj. OFF/ON
Gain
Level
Calib. Lamp Normal/Ring/Both
Recog Adjust Correct OFF/ON
Recog Adjust Point X (Horizontal) . mm
Y (Vertical) . mm
Tg0699-PM-D2
1. Pattern Program Data Sheets
0207-001 Chapter 1 5-4
Pattern Program Date of Preparation
Comment 1 Prepared by
Comment 2
Screen Recognition
Scr. Recog Function 2PT.
Center Recognition OFF/ON
Fiducial Mark #1 X (Horizontal) . mm
Y (Vertical) . mm
Recog. Mode Mark/Model/Model+Mark
Code
Auto Gain Adj. OFF/ON
Gain
Level
Fiducial Mark #2 X (Horizontal) . mm
Y (Vertical) . mm
Recog. Mode Mark/Mode/Model+Mark
Code
Auto Gain Adj. OFF/ON
Gain
Level
Mark Data
Code Figure Size D1 Size D2 Rcg Area Pol. Level Lighting
1 . mm . mm . mm Bright/Dark High/Middle/Low Normal
2 . mm . mm . mm Bright/Dark High/Middle/Low Normal
3 . mm . mm . mm Bright/Dark High/Middle/Low Normal
4 . mm . mm . mm Bright/Dark High/Middle/Low Normal
5 . mm . mm . mm Bright/Dark High/Middle/Low Normal
6 . mm . mm . mm Bright/Dark High/Middle/Low Normal
7 . mm . mm . mm Bright/Dark High/Middle/Low Normal
8 . mm . mm . mm Bright/Dark High/Middle/Low Normal
9 . mm . mm . mm Bright/Dark High/Middle/Low Normal
10 . mm . mm . mm Bright/Dark High/Middle/Low Normal
Setup Data
All Conveyor Setup ON/OFF
Two Camera Auto Calib. ON/OFF
Screen Recog ON/OFF
Prntng Prs. Adj. ON/OFF
Tg0699-PM-D2
1. Pattern Program Data Sheets
0207-001 Chapter 1 5-5
Pattern Program Date of Preparation
Comment 1 Prepared by
Comment 2
Automatic Stop
Hand Cleaning Stop (PCB) pcs.
Hand Cleaning Stop (CLNG.) times
Solv. Empty Stop (CLNG.) times
Paste Supply Interval Mode Paste Detect/Print PCB
Paste Empty Stop (PCB) pcs.
Paste Detect pcs.
Cleaning
Cleaning Area Origin +/- . mm
Depth +/- . mm
Cleaning Interval times
Mode 1 (For.) NO WIPE/DRY/WET/VAC+DRY/VAC+WET
2 (Back.) NO WIPE/DRY/WET/VAC+DRY/VAC+WET
3 (For.) NO WIPE/DRY/WET/VAC+DRY/VAC+WET
4 (Back.) NO WIPE/DRY/WET/VAC+DRY/VAC+WET
Cleaning Speed mm/sec
Paper Feed Pitch mm/sec
Solv. Dispense Time . sec