GL541操作手册.pdf - 第185页
4 - 17 V ersion 2.0 Chapter 2 Explanation of Proper Data 40. MG4LMS LMS_Flag = 0 Specify whether the machine is HELPS-compatible or not HELPS-compatible. [0]: Off: Non HELPS-compatible machine [1]: On: HELPS-compatible m…
Chapter 2 Explanation of Proper Data
24. MG4BUI Busy_Invalid = 0
Specify whether or not the machine refers to board request signals from the next
stage (when unloading a board).
[0]: No: Refer to board request signals from next stage
[1]: Yes: Ignore board request signals and feed out boards when they become
available.
Standard setting: 0
25. MG4CVC Conveyor_Control = 0
Specify whether the machine is fitted with the automatic conveyor width adjustment
mechanism.
[0]: Manu: Manual conveyor adjustment
[1]: Auto: Automatic conveyor adjustment
Standard setting: 0
26. MG4CVAL Conveyor_Adj_Limit (0.05 to 1.00) [mm] = 50
Specify the tolerance for the conveyor width setting when using automatic conveyor
width adjustment
Standard setting: 50
27. MG4CVSO Conveyor_Stop_Offset (0.00 to 2.00) [mm] = 30
Specify the offset value for stopping the motor at the target position when using
automatic conveyor width adjustment.
Standard setting: 30
28. MG4CVAT Conveyor_adj_Timer (0 to 120000) [msec] = 60000
Specify the time for automatic conveyor width adjustment. If this time is exceeded, a
time-up error occurs.
Standard setting: 60000
29. MG4WMAL Width_Max_Limit (0.00 to 655.35) [mm] = 360
Specify the maximum conveyor width.
Standard setting: 360.00
30. MG4WMIL Width_Min_Limit (0.00 to 655.35) [mm] = 50
Specify the minimum conveyor width.
Standard setting: 50.00
4 - 16
Version 2.0
GL-541E Operation
Part 4
4 - 17
Version 2.0
Chapter 2 Explanation of Proper Data
40. MG4LMS LMS_Flag = 0
Specify whether the machine is HELPS-compatible or not HELPS-compatible.
[0]: Off: Non HELPS-compatible machine
[1]: On: HELPS-compatible machine
Standard setting: 0
41. MG4CELL Cell_Status = 0
Specify the cell status.
[0]: Unit Unit cell
[1]: Active Active cell
[2]: Passive Passive cell
Standard setting: 0
42. MG4CHGOM Change_Over_Mode (0 to 200) = 0
Specify the board type report for a HELPS machine.
[0]: Manual terminate
[2]: Pattern code 1 (upper surface)
[4]: Bar code 1 (upper surface)
[5]: Bar code 2 (lower surface)
[25]: Bar code (when using two bar codes; both surfaces)
Standard setting: 0
43. MG4AUTOS Auto_Start = 0
Specify whether the machine enters automatic operation without the START button
being pressed when changeover is complete on a HELPS machine.
[0]: No: After changeover is complete, the START button is enabled
[1]: Yes: After changeover is complete, the machine starts automatically
Standard setting: No
44. MG4BKPC Backup_Plate_Check = 0
Specify whether a back-up plate change request is issued.
[0]: No: No backup plate change request is issued
[1]: Yes: A backup plate change request is issued
Standard setting: No
GL-541E Operation
Part 4
Chapter 2 Explanation of Proper Data
45. MG4CMLS Command_Line_Status = 0
Specify the mode of transmission with the LAN
[0]: RS232C: Use RS232C
[1]: LAN: Use LAN
Standard setting: 0
46. MG4CMLP Command_Line _Port (0 to 30) = 0
Specify the communication board port number when an RS-232C is used.
0: Command line is not used.
11 – 16: Port numbers 1 to 6 on the first VM1440 board
Standard setting: 0
48. MG4BUZW Buzzer_Warning = 0
Specify whether a buzzer sounds when HELPS changeover is performed.
[0]: On: Buzzer will sound
[1]: Off: Buzzer will not sound
Standard setting: 0
49. MG4PROT Process_Timer (0 to 120000) [msec]
Specify the protocol timer value.
Standard setting: 10000
Note: A setting of about 2000 ms is appropriate.
50. MG4RDT Reader Type (0 to 9) = 0
Specify the code reader type when using a code reader to identify the board types on
a HELPS machine.
[0]: Fuji standard bar-code reader
[1]: Fuji standard pattern code reader
[2]: AT&T bar-code reader
[3]: Keyence bar-code reader
Standard setting: 0
4 - 18
Version 2.0
GL-541E Operation
Part 4