00196457-05_UM_SX12DX12_SR706_EN.pdf - 第22页
1 Introduction User Manual SIPLACE SX1/SX2/DX1/DX2 1.3 Machine description From software version SC.706.xx Version 06/2012 EN 22 1.3.2 Serial number of the machine The serial num ber of the machine ca n be found on the i…
User Manual SIPLACE SX1/SX2/DX1/DX2 1 Introduction
From software version SC.706.xx Version 06/2012 EN 1.3 Machine description
21
1.3 Machine description
1.3.1 The SIPLACE principle
The placement heads pick up the components from the feeder modules (fixed position) on the
component trolleys, the DX table/DX changeover table or from the trays of the waffle pack changer
and then place the waiting boards.
The SIPLACE SX1/SX2 placement machine has one placement area and a single or dual con-
veyor. Two boards can be placed at the same time on dual conveyors.
The SIPLACE DX1/DX2 placement machine has one placement area and a single or dual con-
veyor. Two boards can be placed at the same time on dual conveyors.
The principle of "stationary component supply" and "stationary PCB", which have proven them-
selves in the other SIPLACE machines, offer a range of decisive benefits:
– Refilling components and splicing on tapes does not cause downtime.
– The vibration-free component feeder means that even the smallest components (e.g. 01005)
are picked up reliably.
– The PCB, which does not move during the placement process, prevents the components slip-
ping.
– The combination of placement heads with nozzle changers always guarantees an optimum
nozzle configuration for every placement process, thus minimizing traversing paths and opti-
mizing the placement sequence.
High flexibility, efficiency and reliable setups are the guarantee for top productivity in the SIPLACE
machines.
Minimum down times increase utilization and thus help to increase productivity.
1 Introduction User Manual SIPLACE SX1/SX2/DX1/DX2
1.3 Machine description From software version SC.706.xx Version 06/2012 EN
22
1.3.2 Serial number of the machine
The serial number of the machine can be found on the inside of the machine frame at location 1.
1
Fig. 1.3 - 1 Position of typeplate with the serial number (example of SX1/SX2 machine)
(T) Direction of travel
(1) Typeplate
(1)
User Manual SIPLACE SX1/SX2/DX1/DX2 1 Introduction
From software version SC.706.xx Version 06/2012 EN 1.3 Machine description
23
1.3.3 EU Declaration of Conformity
The product/device described below
Product: Placement machine
Type: SIPLACE SX1 SIPLACE SX2
item no.: 00519800 00519850 1
Product: Placement machine
Type: SIPLACE DX1 SIPLACE DX2
item no.: 00120600 00120610 1
manufactured by
ASM Assembly Systems GmbH&Co.KG
Rupert-Mayer-Str. 44
81379 Munich 1
conforms to the regulations and standards listed in the EU Declaration of
Conformity provided.
1.3.4 Use as prescribed
The product may only be used for the areas of application specified in the catalogues and techni-
cal descriptions i.e. for the placement of SMD components and may only be used together with
the third party devices and components recommended or approved by ASM Assembly Systems
GmbH & Co. KG. Use for a different or extended purpose is not prescribed.
In the case of incorrect usage, ASM Assembly Systems GmbH & Co. KG will not assume liability
for any damage which occurs and will not guarantee the correct and proper function of machine
components.
Use as prescribed also includes compliance with all the instructions in the user manual.
For the product to operate correctly and reliably, it must have been transported, stored, erected
and assembled correctly and must be operated and maintained with care.
1.3.5 Failure to use as prescribed
Failure to use the product as prescribed can result in both danger to life and limb and material
damage. For this reason, used other than as prescribed is expressly prohibited. In the case of in-
correct usage, ASM Assembly Systems GmbH & Co. KG will not assume liability for any damage
which occurs and will not guarantee the correct and proper function of machine components.