00196457-05_UM_SX12DX12_SR706_EN.pdf - 第221页
User Manual SIPLACE SX1/SX2/DX1/DX2 4 Setting up and commissioning From software version SC.706.xx V ersion 06/2012 EN 4.3 Setting up the machine 221 4.3.3.2 Fitting the indicator lamp Insert the indicator lamp into th…
4 Setting up and commissioning User Manual SIPLACE SX1/SX2/DX1/DX2
4.3 Setting up the machine From software version SC.706.xx Version 06/2012 EN
220
area of the machine underside (see fig. 4.1 - 4, page 208).
– Do not increase the distance between the forks so that the machine is lifted outside this con-
tact surface. This would lead to deformation of the machine frame and/or damage to the ca-
bles and leads.
Make sure that the forks are evenly loaded when you lift the machine. A firm support between
the forks and machine will prevent the machine tilting when it is raised. This will also prevent
a one-sided load on the machine feet, which would deform the fixing of the machine feet. We
recommend that a second person watch the machine as it is raised, and make sure that the
machine does not tip to one side when lifted with the fork-lift.
WARNING 4
When you are transporting the machine, make sure that all the feet are clear of the floor. If they
are not clear, the feet will drag along the floor or bump into obstacles. This could damage the
machine foot fixing in the machine frame.
4.3.3 Fitting attached parts
The machine is delivered with the monitor, operating panel, keyboard and indicator lamp disman-
tled. To fit these components, proceed as follows:
– To fit the indicator lamps see section 4.3.3.2
, page 221
– To fit the operating panel see section 4.3.4, page 221
– To fit the monitors see section 4.3.3.4, page 221
– Hook up the keyboard fixture and connect the keyboard.
– Place the tape container and waste tape container under the DX tables (DX1/DX2 only).
4.3.3.1 Checking and setting the protective cover switch
Check the function of the protective cover switch (see 2.5.1 on page 57).
Adjust the protective cover switch if necessary (see service manual).
User Manual SIPLACE SX1/SX2/DX1/DX2 4 Setting up and commissioning
From software version SC.706.xx Version 06/2012 EN 4.3 Setting up the machine
221
4.3.3.2 Fitting the indicator lamp
Insert the indicator lamp into the hole until the lamp tube projects sufficiently into the terminal
beneath.
Connect the cable for the indicator lamps to the connector. The cable with connector is lo-
cated in the tube.
Tighten the two screws on the terminal so that the indicator lamp is clamped into place.
4.3.3.3 Fitting the operating panel
Use the 4 fastening screws to fix the operating panel to the monitor mount and then connect
the cable.
Check the cable connections.
4.3.3.4 Fixing the monitors
Use the 4 fastening screws to fix the monitor to the monitor mount and then connect the cable.
Check the cable connections.
4.3.4 PCB conveyor height on the machine
The machine can be set to the following PCB conveyor heights:
900 mm ± 15 mm 4
930 mm ± 15 mm (standard height) 4
950 mm ± 15 mm (SMEMA height) 4
PLEASE NOTE 4
The PCB conveyor height is the distance between the top edge of the PCB conveyor belt and the
bottom edge of the machine feet.
4 Setting up and commissioning User Manual SIPLACE SX1/SX2/DX1/DX2
4.3 Setting up the machine From software version SC.706.xx Version 06/2012 EN
222
4.3.5 Tools and equipment
You will need the following tools and equipment to adjust the height of your machine:
– Open double-ended ring spanner, size 20, Item No. 03080496-01
– Torque wrench with setting scale, Item No. 03080498-01 and extension 1/2 inch, Item No.
03080499-01
– Hexagonal screwdriver bit, size 12 Item No. 03080501-01
– Hexagonal screwdriver bit, size 14 Item No. 03080502-01
– Allen key, for hexagon socket head screws for fixing the machine feet with a grub screw
– Shaft spirit level (accuracy 0.02 mm/m), item no. 00353825-01
– Measuring device for machine alignment, Item No. 03075826-01
as support for the shaft spirit level used to align the gantries. 4
– SX/DX machine alignment gauge 2 assembly, item no. 03077785-01
– SX/DX machine alignment gauge 1 assembly, item no. 03077777-01
for alignment to the PCB conveyors in the line 4
– Fork lift truck (specification see 4.1.4.3 on page 205).
– Air cushion transport system: SIPLACE HSxx, Item No. 00119002-S01 (optional)