00196457-05_UM_SX12DX12_SR706_EN.pdf - 第279页
User Manual SIPLACE SX1/SX2/DX1/DX2 5 Working with the machine From software version SC.706.xx V ersion 06/2012 EN 5.10 Setting up the feeder modules 279 PLEASE NOTE 5 Do not press the lever if a component tape is insert…
5 Working with the machine User Manual SIPLACE SX1/SX2/DX1/DX2
5.10 Setting up the feeder modules From software version SC.706.xx Version 06/2012 EN
278
On standby, the status display (item 2 in fig. 5.10 - 1, page 277) lights up green if the X-axis feeder
module is contained in the current setup. If the feeder module is not contained in the current setup,
the status display remains off.
The X feeder module is locked in position in the changeover table by a latch, and cannot be pulled
out. The procedure for removing feeder modules from the changeover table is as follows:
Press the removal handle (item 1 in fig. 5.10 - 1, page 277). The removal handle jumps
out and the status display goes out.
Wait approximately 1 second until the lock (item 4 in fig. 5.10 - 1, page 277) releases the
feeder module.
Use the removal handle to pull the feeder module out of the changeover table. If you wait
longer than 5 seconds, the feeder module will be locked once more. The status display
lights up red and the message (item 3 in fig. 5.10 - 1
, page 277) "Handle --->>" appears
on the LCD display.
Engage the removal handle once more. If the X feeder module is contained in the current
setup, the status display lights up green and the track number and increment are appear
on the LCD display once more.
Press the removal handle again (item 1 in fig. 5.10 - 1, page 277) and now pull the feeder
module out of the changeover table.
5.10.3 Using the X feeder module
5.10.3.1 Check the X feeder module before using it
Check the following points before you use a feeder module on the changeover table:
The feeder module must be in perfect condition.
Tap the cover foil rocker (item 2 in fig. 5.10 - 2, page 280) lightly to make sure that it has
not
jammed.
Check that the area around the pickup window (item 3 in fig. 5.10 - 2, page 280) is free
from loose components.
PLEASE NOTE 5
Empty the component disposal compartment (item 5 in fig.5.10 - 2
, page 280), before you
shake components out of the feeder module.
Press the lever (item 4 in fig. 5.10 - 2, page 280) forward slightly to open the pickup win-
dow (item 3 in fig. 5.10 - 2
, page 280). This will raise the pick-up window slightly.
User Manual SIPLACE SX1/SX2/DX1/DX2 5 Working with the machine
From software version SC.706.xx Version 06/2012 EN 5.10 Setting up the feeder modules
279
PLEASE NOTE 5
Do not press the lever if a component tape is inserted. The tensioned cover foil would move
the component tape on and expose the components.
Remove any loose components from beneath the pick-up window.
Close the pickup window (item 3 in fig. 5.10 - 2), by returning the lever (item 4 in fig. 5.10
- 2) to its original position.
Remove loose components from the changeover table with a brush or use a vacuum
cleaner with appropriate nozzle.
PLEASE NOTE 5
If the component tape is already inserted, cut it off flush with the front edge of the feeder mod-
ule.
If the removal handle (item 1) is still protruding, then latch it in place.
5 Working with the machine User Manual SIPLACE SX1/SX2/DX1/DX2
5.10 Setting up the feeder modules From software version SC.706.xx Version 06/2012 EN
280
5
Fig. 5.10 - 2 Check the X feeder module before using it
(1) Removal handle
(2) Cover foil rocker
(3) Pickup window
(4) Lever for raising and latching the pick-up window
(5) Component disposal compartment