SiplaceX4_en.pdf - 第117页

1 - 47 S tudent Guide SIPLACE X Edition 09/2005 3 Communication and Control 47 3.5.1.3 One Wire Bus in the Siplace X With the Siplace X-machine the One Wire Bus is in tegreted in a separa te CA T5 cabel, which start from…

1 - 46

Student Guide SIPLACE X

3 Communication and Control Edition 09/2005

3.5.1.2 One Wire Bus in the HF Machines

The one wire bus in integrated into the machine CAN bus cable and therefore divided into place-

ment areas 1 and 2. The structure or arrangement of the CAN stations is identical with that of the

machine CAN bus. Pin 1 (wire 1) of the machine CAN bus is used for the one wire system.

Fig. 3.5 - 2 Overview of one wire subsystems e.g. BB1 on the HF machine

Depending on the machine configuration (1 or 2 gantries) the one wire bus structure in PA2 is iden-

tical with that in PA1.

Vision

Control unit

Sector 4

Conveyor

Control

Axis unit

BB 1

Option: Check reject bin

or terminating plug

Attention: no CAN-

termination resistor

COM Board

I/O SUB Module

Sector 4

One Wire Bridge

(driver)

Nozzle Changer

Hub (Coupler)

Temp.sensor

CO-Table 4

Cutter

Head

plate

Control Board

NC (C&P20)

Row 1

Control Board

NC (C&P20)

Row 2

Trailing Unit Interface

Gantry 4

1 Wire Board

(Trailing Unit

Interface)

Temp.sensor

Nozzle Changer

Hub (Coupler)

CO-Table 1

Cutter

Control Board

NC (C&P20)

Row 1

Control Board

NC (C&P20)

Row 2

Trailing Unit Interface

Gantry 1

1 Wire Board

(Trailing Unit

Interface)

Temp.sensor

Head

plate

Temp.sensor

Gantry

recognition

Option: Check reject bin

or terminating plug

Attention: no CAN-

termination resistor

TQM Module

(Master)

RS232

Machine CAN Bus with

One Wire

Gantry

recognition

1 - 47

Student Guide SIPLACE X

Edition 09/2005 3 Communication and Control

3.5.1.3 One Wire Bus in the Siplace X

With the Siplace X-machine the One Wire Bus is integreted in a separate CAT5 cabel, which start

from the Main- and Subdistributor up to the trailling interface. From the trailing interface up to the

head interface the one wire bus goes through the trailling cable. So that the cable structur are dif-

ferent but not the function of the one wire bus.

Fig. 3.5 - 3 Overview of one wire subsystems e.g. PA1 on the Siplace X

Depending on the machine configuration (1 or 2 gantries) the one wire bus structure in PA2 is iden-

tical with that in PA1.

Vision control

unit

Sector 4

Transport

Control unit

Axis unit

PA 1

COM Board

I/O SUB Module

Sector 4

One Wire Bridge

(driver)

Nozzle changer

Hub (Coupler)

Gantry 4

CO-Table 4

Tape cutter

Conrol board

NC (C&P20)

row 1

Control board

NC (C&P20)

row 2

Trailing -Interface

Gantry 4

CO-Table 1

Tape cutter

Trailing-Interface

Gantry 1

Temp.sensor

Head

plate

Temp.sensor

Option: Check reject bin

or terminating plug

Attention: no CAN-

termination resistor

TQM Module

(Master)

RS232

Machine CAN Bus

1 Wire CAT5

Gantry 4

Headinterface

1 Wire CAT5

Gantry 4

Temp.sensor

Head

plate

Temp.sensor

Gantry

recognition

Headinterface

1 Wire CAT5

Distributor

24V for the nozzle changer

1 Wire CAT5 cable

Nozzle changer

Hub (Coupler)

Gantry 1

Control board

NC (C&P20)

row 2

Conrol board

NC (C&P20)

row 1

Option: Check reject bin

or terminating plug

Attention: no CAN-

termination resistor

Gantry

recognition

1 - 48

Student Guide SIPLACE X

3 Communication and Control Edition 09/2005

Function description: 3

When the machine is switched on, each one wire bus is assigned a fixed CAN ID.

One wire in PA1 --> CAN ID: 07d0

One wire in PA2 --> CAN ID:07c0

During initialization of the bus system, each station registers with the master, after which the bus

is ready for operation.

In the non operative mode, the voltage level is 5 V on the one wire bus.

A repeat initialization can be performed with the CACCIA tool (see Function Control and Trouble-

shooting for Service Work).

Pin assignment in machine CAN bus:

Fig. 3.5 - 4 Pin assignment for sub D connectors

One wire bus components 3

Assemblies:

1. 1 wire RS232 bridge on the SUB/MAIN module (to be later integrated into the I/O module)

2. 1 wire CAT 5 Gantry on the trailing interface (board between CAN bus and trailing interface)

3. 1 wire CAT 5 Splitter

4. 1 wire hub for nozzle changer

5. Control board for nozzle changer (integrated into NC, not for DLM heads)

6. 1 set of temperature sensors (replacement only as a set, due to serial number)

7. EEPROM for gantry recognition

120

Ohm

CAN Interrupt95

+24V 1-wire-Bus89

Power Fail74

CAN Reset68

GND53

CAN High47

CAN Low32

GND26

1-wire-Bus 11

AderPin

Pin 1 only for HF machines