FUJI NXT Programming Manual QD004-18.pdf - 第176页

6. Editing Jobs on the Machine (MEdit) QD004-18 166 NXT Programming Manual 3. Select the factory, line, NXT machine a nd then first module in the [M odule list]. A list of the available boards and lanes is displa yed in …

QD004-18 6. Editing Jobs on the Machine (MEdit)

NXT Programming Manual 165

6.6 Skipping Items on the NXT

6.6.1 Skipping boards (from NXT V3.10)

If always a particular board in a panel production lot needs to be skipped for some reason,

it is easy to specify a skip for this board for the production lot. There are a few important

points that should be addressed when using this function.

• When the board to be skipped is specified for the first module, that board is

skipped in all modules after the first module.

• The skip setting is only applied to new panels which means that the setting is

not applied to any panels already loaded.

• Job board skip settings and board skips due to skip marks cannot be overridden

by this function.

• Enable the machine configuration settings related to the skip function (the

procedure is listed below.) Panel conveyance time is lengthened by around 300

ms when these configuration settings are enabled.

• If a certain board is to always be skipped for all production lots, then skip the

board in the job with Fuji Flexa.

• If the boards to be skipped are not set (changes from panel to panel), then use

skip marks to skip the required boards.

Specifying the machine configuration setting to enable this function.

1. Start Accessory Software and click the name of the machine for which to change the

setting in Floor Monitor.

2. If necessary, specify a user ID from the drop-down list and enter a password for the

specified user and click [Log on]. The machine accessories page is displayed.

3. Click [Machine Configuration] in the [Menu] pane. Accessory Software connects to the

machine and receives the machine information. When completed, the settings page is

displayed.

4. Select [Skip boards at the machine setting] from the [Category] drop-down list. The

settings for this category are then displayed.

5. Select the [ON] option for the [Skip boards at the machine] setting.

6. Click [Send to Machine] to send the new setting to the machine. The setting is enabled

once the completed message is displayed.

Skipping a board at the machine.

1. Before loading the panel belonging to the lot for which board skipping is to be performed,

verify that no panels exist inside the first module, and push CYCLE STOP to stop

production.

2. Start MEdit and select [Board skip] from the [Tool] menu. The [Board skip] dialog box

is displayed.

6. Editing Jobs on the Machine (MEdit) QD004-18

166 NXT Programming Manual

3. Select the factory, line, NXT machine and then first module in the [Module list]. A list of

the available boards and lanes is displayed in the [Board skip settings] list.

4. Select the check boxes for the lane and boards to be skipped.

Note: Check boxes for multiple boards can be selected by using the [Shift] or [Ctrl] key. First, hold

down the [Shift] or [Ctrl] key and left-click on the number of the desired boards to highlight

those boards. Then, release the [Shift] or [Ctrl] key and select the check box for any one of

the highlighted boards. This will automatically select the check boxes for all highlighted

boards.

5. Click [OK] to apply the skip settings and then close MEdit.

Note: The new skip setting is only applied to panels that are loaded in the module after this setting

is made.

6. Begin production and load the panels for which the board skip is to be applied.

When boards are specified to be skipped, the skipped boards are displayed in the operation

panels on the modules. Confirm that the boards to be skipped are correct. Be sure to

remove the skip setting when switching to a production lot in which the previously skipped

board is to be produced.

6.6.2 Skipping feeders (from NXT V2.95)

Use this function to skip all the parts from a feeder. This allows production to be completed

for panels when parts are no longer available for the parts that have run out. It is important

to note the following points about this function.

• When parts are skipped, the panel is completed without placing the skipped

parts.

• This function should only be used if it absolutely necessary to skip a part to

complete production such as when a certain part runs out and will be placed on

the panel at a later time once new parts are received.

• This function is designed to be used by line management personnel.

NXTEJM001E

QD004-18 6. Editing Jobs on the Machine (MEdit)

NXT Programming Manual 167

Skipping a feeder on a module.

1. As soon as a part supply runs out during production, the machine waits for the parts to

be supplied in a "recovery up" status. Perform the following steps only if parts are not

available to be resupplied.

2. Push CYCLE STOP at the module in question to stop production for that module.

3. Start MEdit and select [Feeder skip] from the [Tool] menu. The [Feeder skip] dialog box

is displayed.

4. Select the factory, line, NXT machine, and the module in the [Module list]. A list of the

available feeders is displayed in the [Feeder skip settings] list.

5. Select the check box for the feeder with the parts to be skipped.

Note: Check boxes for multiple feeders can be selected by using the [Shift] or [Ctrl] key. First, hold

down the [Shift] or [Ctrl] key and left-click on the number of the desired feeders to highlight

those feeders. Then, release the [Shift] or [Ctrl] key and select the check box for any one

of the highlighted feeders. This will automatically select the check boxes for all highlighted

feeders.

6. Click [Set] to apply the skip setting and then close MEdit.

Note: If a place before setting is set for a skipped part, the place before setting is disabled.

Simultaneously skip the 2 related feeders for the "place before" setting.

7. Push START at the module in question to restart production. Production is continued

without placing parts from the skipped feeder position.

Note: It is not necessary to have a feeder in the skipped position in order to continue production.

However, it is necessary to have an empty drawer set in the skip position if a tray part is

skipped on a tray unit-L.

All of the LEDs for the feeder position are turned on for skipped feeder positions. For tray

parts, skipped positions have a white numbers and the part comment text is grey in the

parts out guidance screen.

Clearing the skip setting for a feeder on a module.

1. Push CYCLE STOP at the module before the module with the skipped part (this

prevents any new panels from being loaded into the next module).

2. Wait until all panels are unloaded from the module with the feeder skip and then push

CYCLE STOP on that module.

3. Start MEdit and select [Feeder skip] from the [Tool] menu. The [Feeder skip] dialog box

is displayed.

4. Select the factory, line, NXT machine, and the module with the skipped feeder in the

[Module list]. A list of the available feeders is displayed in the [Feeder skip settings] list.

5. Clear the check box for the feeder with the parts that are being skipped.

6. Click [Set] to apply the cleared skip setting and then close MEdit.

Note: If a place before setting is set, be sure to clear the skip settings simultaneously for the 2

related feeders with the "place before" setting.

7. Set the new parts in the module in the specified position.

8. Push START at the module in question to restart production. Production is continued

and the newly supplied parts are placed.