FUJI NXT Programming Manual QD004-18.pdf - 第7页

QD004-18 Contents NXT Programming Manual i Contents 1. Introducti on .......................................................... 1 1.1 Notation Convention s Used in the Manual ....... 1 1.1.1 General notation ............…

100%1 / 220
Copyrights
All rights regarding this manual are reserved by Fuji Machine Manufacturing Co., Ltd. This manual may
not, in whole or in part, be reproduced by any means (electronic, mechanical or otherwise), or reused in
any way, without the prior written permission of Fuji Machine Manufacturing Co., Ltd.
Warranty and Liability
Fuji Machine Manufacturing Co., Ltd. accepts no responsibility for situations that may arise due to any of
the following:
• The use of third party parts.
• The use of non-genuine Fuji parts.
• Incorrect settings made by the customer.
• Improper use of Fuji equipment.
Notice
Fuji Machine Manufacturing Co., Ltd. reserves the right to change the content of this manual without
notice.
Every effort has been made to ensure that this manual is correct in every detail. However, please contact
Fuji in the unlikely event that errors or omissions are detected.
Fuji Machine Manufacturing Co., Ltd. accepts no liability whatsoever for damages that may arise as a
result of this manual, with the exception of problems that originate in our products.
QD004-18 Contents
NXT Programming Manual i
Contents
1. Introduction .......................................................... 1
1.1 Notation Conventions Used in the Manual....... 1
1.1.1 General notation ..................................................... 1
1.1.2 Mouse-related notation........................................... 1
2. Fuji Flexa and the NXT ........................................ 3
2.1 Introduction ...................................................... 3
3. Job Builder........................................................... 5
3.1 Introduction ...................................................... 5
3.2 General Steps to Creating NXT Jobs............... 5
3.2.1 Starting by changing an existing job....................... 5
3.2.2 Starting by manually entering sequence data......... 5
3.2.3 Starting by importing centroid CAD data ................ 6
3.2.4 Starting by importing CCIMF files with part data .... 6
3.2.5 Starting by importing MCSIMF files ........................ 7
3.2.6 Starting by importing Allegro CAD data .................. 7
3.2.7 Starting by importing Mentor CAD data .................. 8
3.2.8 Starting by importing CR5000 (PWS/Board
Designer) CAD data ................................................. 8
3.2.9 Starting by importing OrCAD CAD data.................. 9
3.2.10 Starting by importing SFX-J1 CAD data ............... 9
3.2.11 Starting by importing Specctra CAD data ........... 10
3.2.12 Starting by importing PowerPCB CAD data........ 10
3.2.13 Starting by importing PanaCAD data.................. 11
3.3 NXT Job Settings ........................................... 12
3.3.1 Changing the current line to a NXT line................ 12
3.3.2 Adding an NXT line to a job.................................. 13
3.3.3 Configuring an NXT machine................................ 14
3.3.4 Distributing the same part to multiple modules..... 31
3.3.5 Assigning an alternate feeder............................... 32
3.4 Job Settings for Advanced Functions............. 33
3.4.1 Setting auto backup pins ...................................... 33
3.4.2 Specifying a panel edge sequence
Contents QD004-18
ii NXT Programming Manual
(from NXT V3.10) .................................................. 36
3.4.3 Package-on-Package placement (from NXT V4.10)
............................................................................... 39
3.4.4 Using the M6S and single conveyor S
(from NXT V4.30) .................................................. 43
3.4.5 Using the parts presence check function
(from NXT V4.42) .................................................. 45
3.4.6 Using the tray unit-LT and LTC............................ 47
3.4.7 Limiting the number of reels used in a job ........... 57
3.4.8 Specifying the tape pitch and indexing speed in the
job (from NXT V5.15)............................................. 60
3.4.9 Adjusting placement due to panel warp function
(from NXT V5.15) .................................................. 62
3.5 Line Balancing ............................................... 65
3.5.1 Line balancing in Job Builder ............................... 65
3.5.2 NXT Multi Job Line Balancer (option) .................. 65
3.6 Optimizing ...................................................... 70
3.6.1 Optimizing in Job Builder ..................................... 70
3.6.2 NXT Multi Machine Optimizer .............................. 70
3.6.3 Dual job optimizing............................................... 74
3.7 Generating Reports........................................ 76
3.7.1 Manually generating reports................................. 76
3.7.2 Automatically generating reports when the job is
saved ..................................................................... 76
4. Part Data Settings .............................................. 77
4.1 Introduction .................................................... 77
4.2 Part Data........................................................ 78
4.2.1 Part data details ................................................... 78
4.3 Shape Data .................................................... 80
4.3.1 Shape Information tab.......................................... 80
4.3.2 Shape Process tab............................................... 81
4.3.3 Shape Information details .................................... 85
4.3.4 Shape Process details ......................................... 88
4.4 Package Data ................................................ 98
4.4.1 Package Information tab ...................................... 98
4.4.2 Package Process tab ........................................... 98