FUJI NXT Programming Manual QD004-18.pdf - 第69页
QD004-18 3. Job Builder NXT Programming Manual 59 4. If a security warning is d isplayed asking if macros sh ould be enabled (if macr o security is set to "medium"), click [Enable Marc os]. Note: Macros must be…
3. Job Builder QD004-18
58 NXT Programming Manual
The function to limit the number of reels for parts number is then enabled. It is necessary
to then specify the part numbers to limit in the Excel sheet by following the procedures in
the next section.
Specifying the part number reel limits
When the function to limit the number of reels for parts numbers is enabled, the part
numbers and quantity of reels that is to be limited need to be specified by following the
procedures below. These settings are only for the computer they are specified on and are
for all jobs that are optimized on that computer (they are not job specific).
1. Create the job as usual.
2. If the "LimitFeederDuplication" folder has not already been copied to the computer, then
copy the "LimitFeederDuplication" folder from the "Tools" folder on the Fuji Flexa
installation CD-ROM and paste it in the location from which you want to use it.
3. Open this folder and then double-click the "FeederDuplicate.xls" file to open it.
QD004-18 3. Job Builder
NXT Programming Manual 59
4. If a security warning is displayed asking if macros should be enabled (if macro security
is set to "medium"), click [Enable Marcos].
Note: Macros must be enabled for this Excel sheet to function properly.
5. Specify the part numbers for the parts that you want to limit the reel quantity in the
[PartNumber] column and then specify the number of reels possible for each part
number in the [Count] column.
6. Ensure that the entered settings are correct and then click [Save & Export].
7. Optimize the job.
Note: If you want to change the limit settings, then change the Excel sheet, save and export and
then optimize again. The limit settings are used the next time optimization is performed
after the data is saved and exported.
That completes specifying a limit on the number of available reels for part numbers. If you
open a new job and want to limit the number of reels for different part numbers in that job,
you must specify the different part numbers in the Excel sheet and then save and export it.
01PRG103E
3. Job Builder QD004-18
60 NXT Programming Manual
3.4.8 Specifying the tape pitch and indexing speed in the job (from
NXT V5.15)
Until now the pitch and indexing speed of tape have been set using the dip switches on the
feeder itself. However, from this version onwards these can be set in the job.
Also, for W12 and larger feeders, pitch sizes that could not be set using the dip switches on
the feeder (64, 68, and 72 mm) can now be set. (Refer to the illustration below.)
Feeder types and pitches that can be set in the job
Required items
Intelligent Feeders
• W04b/W08b/W08c (V1.10 or higher)
• Not including W04b/W08b/W08c (V3.14 or higher)
Software
• NXT application (V5.15 or higher)
• Fuji Flexa (V5.0.0 or higher)
How to specify settings
Set [Feed Pitch], [Indexing Speed] and [Assign Feeder Indexing Settings] in the job
Package Data.
1. Open the job in Fuji Flexa.
2. Select the [Package Data] tab on the job information bar in Job Builder.
3. Double click the appropriate Package Data.
4. Select the [Package Information] tab from the [Package Data] screen.
W12
W16
W24
W32
W44
W56
W72
W88
W104
W120
W136
W152
W168
W184
W200
1
W04b
W08b/W08c
W08
Feeder type
Pitch (mm)
24812 60 6864 7216 20 24 28 32 36 40 44 48 52 56 73 ~ 100
01PRG-0113E
O: Supported X: Not supported : Can be set in the job
O
O
O
X X
X