XP Type II 工程师培训手册 (2.0).pdf.pdf - 第10页
C C h h a a p p t t e e r r 1 1 I I n n i i t t i i a a l l A A d d j j u u s s t t m m e e n n t t
FK-9F98-34 XP Series Type II Training Text for Service Engineers
Edition 2.0 XP142E Contents
5.9 Measuring the Vacuum Pressure............................................................... 5-12
Chapter 6 Proper Data Measurements
Section No. .................................................................................................. Page No.
6.1 Parts Camera Setting................................................................................. 6-1
6.2 Parts Camera Center Adjustment .............................................................. 6-1
6.3 Prism Position ............................................................................................ 6-4
6.4 Parts Camera Brightness Adjustment ........................................................ 6-5
6.5 Parts Camera Focus .................................................................................. 6-6
6.6 Parts Camera Resolution Measurement (Standard) .................................. 6-9
6.7 Parts Camera Resolution Measurement (Low Parts)................................. 6-11
6.8 Mark Camera Setting ................................................................................. 6-13
6.9 Mark Camera Focus................................................................................... 6-14
6.10 Mark Camera Brightness ......................................................................... 6-14
6.11 Mark Camera Resolution ......................................................................... 6-15
6.12 Mark Positions and Angle Measurement ................................................. 6-16
6.13 Measuring the Board Origin ..................................................................... 6-17
6.14 Measuring Z0 ........................................................................................... 6-18
6.15 Measuring the Maximum Nozzle Height .................................................. 6-19
6.16 Reset Cylinder.......................................................................................... 6-20
6.17 Measuring the R-Axis Offset .................................................................... 6-21
6.18 MFU Pickup Position................................................................................ 6-22
6.19 Pickup Height........................................................................................... 6-23
6.20 Feeder Indexing ....................................................................................... 6-24
6.21 Retract Position........................................................................................ 6-25
6.22 Parts Reject Position................................................................................ 6-26
6.23 Parts Gage Pickup Positions.................................................................... 6-26
6.24 Matrix Data............................................................................................... 6-27
6.25 Conveyor Width Changer......................................................................... 6-28
Chapter 7 Operation and Accuracy
Section No.................................................................................................... Page No.
7.1 Checking Idle Operation............................................................................. 7-1
7.2 Glass Parts PAM........................................................................................ 7-2
7.2 Reverse PAM ............................................................................................. 7-5
Supplemental Information
XP142E Servo Amp Parameter List
V2.00 Proper Data List
Mechanical Stopper Locations
Fuji Machine Mfg. Co., Ltd. Okazaki.
SMT Equipment Quality Assurance Dept.
CS Section
C
C
h
h
a
a
p
p
t
t
e
e
r
r
1
1
I
I
n
n
i
i
t
t
i
i
a
a
l
l
A
A
d
d
j
j
u
u
s
s
t
t
m
m
e
e
n
n
t
t
FK-9F98-34 XP Type II Series Training Text for Service Engineers
Edition 2.0 XP142E – Chapter 1 Initial Adjustment Page 1 of 8
Fuji Machine Mfg. Co., Ltd.Okazaki
Chapter 1 – Initial Adjustment
1.1 Leveling
1. Place two track levels at position A, shown in the following diagram:
3 2
A
4 1
2. Carry out initial leveling at points 1,2,3,4, then lock all 8 leveling sheets.
3. Leveling tolerance is 0.10mm/1000mm.
1.2 Power and Air Connection
Power Supply Connection
1. Open the power supply box at the lower right hand side of the machine and pull the power
line through the bottom of the box.
2. Connect the ground terminal and the ground wire first.
L1 L2 L3
Red
3. Connect the three wires of the power supply cable to the three breaker box (KG41B)
terminals.
L1: red L2: white L3: black
SMT Equipment Quality Assurance Dept.
1 – 1 CS Section