XP Type II 工程师培训手册 (2.0).pdf.pdf - 第137页
FK-9F98-34 XP T ype II Series T raining T ext for Service Engineers Edition 2.0 XP242E – Chapter 4 Loader Adjustment Page 12 of 12 4. 10 Conveyor Wid th and Movement 1. Ensure that the width change can be carried out smo…
FK-9F98-34 XP Type II Series Training Text for Service Engineers
Edition 2.0 XP242E – Chapter 4 Loader Adjustment Page 11 of 12
4.9 Board Sensors
1. For each board sensor adjustment, use a FUJI96 board.
2. Set the sensor dial to its maximum volume (to clockwise).
Note: Ensure that when the sensor volume is at the maximum it does not detect any part
of the X and Y-axes moving above it. If the X or Y-axes affect the sensor, reduce the
sensor volume.
To ensure that there is enough clearance between the board and sensors, adjust the
distance between the board underside and the sensor top surface to the following
distances:
Board
Sensor
In- lifter board arrival sensor ····························· 27mm
Main conveyor board deceleration sensor········· 25.5mm
Main conveyor board arrival sensor ················· 25.5mm
Main conveyor board pass sensor ···················· 30mm
Out conveyor board pass sensor....................... 25.5mm
40mm
1
2
3
4
36mm
5
60mm
5mm
Out-conveyor
In-lifter Main lifter
1. In-lifter board arrival sensor ································ X01B InStArrvChk
2. Main conveyor board deceleration sensor ········· X01C MainStDecelPnt
3. Main conveyor board arrival sensor···················· X01D MainStArrvChk
4. Main conveyor board pass sensor ······················ X022 MainStPassChk
5. Out conveyor board pass sensor ························ X020 OutStPassChk
Fuji Machine Mfg. Co., Ltd. Okazaki.
SMT Equipment Quality Assurance Dept.
4 – 11 CS Section
FK-9F98-34 XP Type II Series Training Text for Service Engineers
Edition 2.0 XP242E – Chapter 4 Loader Adjustment Page 12 of 12
4. 10 Conveyor Width and Movement
1. Ensure that the width change can be carried out smoothly, when the conveyor is moved
to its Min. (50mm or less) ~ Max. (356mm or greater) width.
Note: Do not use the conveyor auto width changer, as this is not adjusted yet.
2. Set the entrance of the In-conveyor to 130mm. Check a few points along the conveyor
width from entrance to exit. The difference between the maximum width and minimum
width should be within 0.5mm. If it is out of the tolerance, please contact FUJI.
3. The speed of board loading and the speed of the conveyor width changer are set at FUJI
prior to machine shipment. Changing these speeds is not recommended. However for
your reference the location and function of the conveyor speed controllers are given
below:
Loading Function Controller
Board Loading (Normal speed) T1VR1
Board Loading (Deceleration) T1SP1
Conveyor width change T1SP2
T1SP1 T1SP2
T1VR1
Main rela
y
board
Speed control
board cover
Electric Box Doo
r
Side1: Rear of the
Electric Box, top
left connector on
the main relay
board.
Side1; Back of
the right door of
the bottom Box.
Fuji Machine Mfg. Co., Ltd. Okazaki.
SMT Equipment Quality Assurance Dept.
4 – 12 CS Section
C
C
h
h
a
a
p
p
t
t
e
e
r
r
5
5
P
P
e
e
r
r
i
i
p
p
h
h
e
e
r
r
a
a
l
l
A
A
d
d
j
j
u
u
s
s
t
t
m
m
e
e
n
n
t
t
s
s