00197498-03_UM_SiplaceCA-Serie_EN.pdf - 第296页

5 Setting up and Commissioning User Manual SIPLACE CA-Series 5.5 Setting Up the Placement Machine From software version SC.708.0 Edition 12/2014 EN -DR AFT 296 5 Fig. 5.5 - 10 Fitting the grounding cable 5 5 5 5 5 5.5.7.…

100%1 / 518
User Manual SIPLACE CA-Series 5 Setting up and Commissioning
From software version SC.708.0 Edition 12/2014 EN -DRAFT 5.5 Setting Up the Placement Machine
295
Insert the mandrel (item 5 in fig. 5.5 - 9) for the transportation cover into the hole (item 6 in
fig. 5.5 - 9
) for the second half of the extension kit.
Position the second half of the extension kit so that the assembly bracket lies on the assembly
bar (item 7 in fig. 5.5 - 8
).
Fasten this second half of the placement machine with 2 fillister head screws M6x16 and the
corresponding washer (item 3 in fig. 5.5 - 8
).
5.5.7.3 Fastening the Hexagonal Shaft Guidance
When using a single conveyor, fasten one guidance for the hexagonal shaft (item 8 in fig. 5.5
- 7) to the extension kit with two fillister head screws M6x16 and washers
When using a dual conveyor, fasten two guidances for the hexagonal shaft (item 8 in fig. 5.5
- 7) to the extension kit with two fillister head screws M6x16 and washers
5.5.7.4 Establishing Cable Connections - Extension Kit on the PCB Output Side
5
5
5
5
5.5.7.5 Fitting the Ground Cable for the Doors
Fasten the two ground cables for the doors (item 4 in fig. 5.5 - 8) to the machine frame as
follows:
Left side of extension kit
(viewed in direction of transport)
Connector/cable To connector/cable
EMERGENCY STOP button
Start/Stop button
X63/03020687 X63/03002526
Protective cover switch, location 3 X53/03020409 X53/03002528
Button for the COT insert,
location 3
X232/03021056 X232/03021053
Right side of extension kit
(viewed in direction of transport)
Connector/cable To connector/cable
Start/Stop button
Switch, PCB conveyor cover
X62/03020410 X62/03002525
Protective cover switch, location 2 X52/03006476 X52/03002527
Button for the COT insert,
location 2
X222/03021056 X222/03021052
5 Setting up and Commissioning User Manual SIPLACE CA-Series
5.5 Setting Up the Placement Machine From software version SC.708.0 Edition 12/2014 EN -DRAFT
296
5
Fig. 5.5 - 10 Fitting the grounding cable
5
5
5
5
5
5.5.7.6 Checking and Setting the Protective Cover Switch
Check the function of the protective cover switch (item 7 in fig. 5.5 - 9, page 294).
Adjust the protective cover switch if necessary (see service manual).
Hex nut M
Spring washer M, DIN 7980
Washer M, DIN 125
Cable lug, annular
Contact washer
User Manual SIPLACE CA-Series 5 Setting up and Commissioning
From software version SC.708.0 Edition 12/2014 EN -DRAFT 5.5 Setting Up the Placement Machine
297
5.5.7.7 Installing the Bottom Hand Guard
The placement machines are only supplied with one bottom hand guard. However, if the place-
ment machines are installed in a line, there will be no hand guard between neighboring output and
input conveyors.
5
5
Fig. 5.5 - 11 Fitting the "bottom" hand guard to the PCB output side
(1) "Bottom" hand guard [03003432-01]
WARNING
Unauthorized Access!
A missing hand guard between the input and output sides of the placement machine in a
production line could lead to unauthorized access if staff reach into the inside of the place-
ment machine.
Always fit the bottom hand guard at the input side of the first placement machine and
on the output side of the last placement machine in a line [03003432-01] with 4 hexa-
gon socket-head screws M4x12.