00197498-03_UM_SiplaceCA-Serie_EN.pdf - 第373页

User Manual SIPLACE CA-Series 6 Working with the Machine From software version SC.708.0 Edition 12/20 14 EN -DRAFT 6.7 Configuring the Feeder Modules 373 6.7.3.2 Inserting the X Feeder Module into the Changeover T able 6…

6 Working with the Machine User Manual SIPLACE CA-Series

6.7 Configuring the Feeder Modules From software version SC.708.0 Edition 12/2014 EN -DRAFT

372

 Remove any loose components from beneath the pick-up window.

 Close the pickup window (item 3) by returning the lever (item 4) to its original position.

 Remove loose components from the changeover table with a brush or use a vacuum

cleaner with appropriate nozzle.

 If the removal handle (item 1) is still protruding, then latch it in place.

Fig. 6.7 - 2 Checking the X feeder module before use

PLEASE NOTE

 If the component tape is already inserted, cut it off flush with the front edge of the

feeder module.

(1) Removal handle (2) Cover foil rocker

(3) Pickup window (4) Lever for raising and latching the pick-up

window

(5) Component disposal compartment

User Manual SIPLACE CA-Series 6 Working with the Machine

From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.7 Configuring the Feeder Modules

373

6.7.3.2 Inserting the X Feeder Module into the Changeover Table

Fig. 6.7 - 3 Inserting the X feeder module into the changeover table

(1) Front slider guide for the X feeder module

(2) Back slider guide for the X feeder module

(3) "Back" centering pin on the X feeder module

(4) "Front" centering pin on the X feeder module

(5) Recesses in the centering bar for holding the "back" centering pin

(6) Centering holes on the changeover table for holding the "front" centering pin

(7) Locking latches

(8) Guide profile for the changeover table (Ω profile)

(9) Insertion aid for the feeder module

 Place the front slider guide (item 1) of the feeder module on the insertion aid (item 9) for the

component table.

 Hold the feeder module vertically and push it forward, along the guide profile (item 8). The

front (item 1) and rear (item 2) slider guides of the feeder module slide on the guide profile

(item 8).

 Carefully push the feeder module further until the "front" centering pin (item 4) is pushed into

the centering hole (item 6).

6 Working with the Machine User Manual SIPLACE CA-Series

6.7 Configuring the Feeder Modules From software version SC.708.0 Edition 12/2014 EN -DRAFT

374

 Check the "back" centering pin (item 3) of the feeder module as you do so. This must slide

easily into the recess (item 5) in the centering bar, otherwise the feeder module is not seated

vertically on the component table or it was not placed on the guide profile (item 8) correctly.

 The locking latch (item 7) engages with the locking roller of the feeder (item 1 in fig. 7.1 - 2).

If you have forgotten to engage the removal handle (item 1 in fig. 6.7 - 2

, page 372) the status

display

on the feeder module's operator panel will light up red after a few seconds. The LCD display

contains the error message "Handle --->>" (see fig. 6.9 - 1

, page 379). 6

 Engage the removal handle (item 1 in fig. 6.7 - 2). The feeder module's status display

now lights up green and the feeder module is on standby. The track number and con-

veyor increment can be read on the LCD display once more.

6.7.4 Inserting the Component Tape into the X feeder Module

6.7.4.1 Checking the X Tape Feeder Module

 When you place the component tape in the feeder module, first check whether there are

any components in the vicinity of the pickup window (item 2 in fig. 6.7 - 5

 Remove any components that you find since they could cause a fault.

6.7.4.2 Preparing the Component Tape for Insertion

 Check that there is a straight cut edge at the start of the component tape.

 If the transport holes are torn or bent, cut off this part of the tape.

 Also make sure that there are no streaks of adhesive on the cover foil.

 Pull around 30 cm cover foil away from the component tape if this does not expose any

components.

PLEASE NOTE

Avoid loss of components

 If there is not enough cover foil available, use the SMD tape threader

for the 8 mm tape:Item no. 00355265-xx

for the 12 mm - tape:Item no. 00356342-xx