00197498-03_UM_SiplaceCA-Serie_EN.pdf - 第389页
User Manual SIPLACE CA-Series 6 Working with the Machine From software version SC.708.0 Edition 12/20 14 EN -DRAFT 6.14 Docking/Undocking the Compo nent Trolley 389 6 6.14.3 Docking the X-Series Component T rolley 6 Fig.…
6 Working with the Machine User Manual SIPLACE CA-Series
6.14 Docking/Undocking the Component Trolley From software version SC.708.0 Edition 12/2014 EN -DRAFT
388
The safety concept for the component trolley changeover prescribes that the user presses a but-
ton (item 1, 2, 3 or 4 in fig. 6.14 - 1
) on the input or output side of the machine, in order to dock or
undock the component trolley. This ensures that the operator is always standing to the side of the
placement machine. In addition, the component trolley can only be docked in if the protective cov-
ers are closed.
6.14.2 Undocking the Component Trolley
Click on the STOP PROCESSING PCB icon in the MAIN VIEW menu.
The PCB in progress will be completed. The icons of the SINGLE FUNCTIONS menu will
then be activated. 6
Click on the desired icon SINGLE FUNCTIONS GANTRY.
Select GANTRY FUNCTIONS.
From this menu, click on the GO TO SET-UP POSITION button.
All the placement heads will move across the PCB conveyor to prevent them being damaged
when the component trolley is changed. 6
Press the appropriate button on the input or output side of the machine (item 1, 2, 3 or 4 in
fig. 6.14 - 1
) until the component trolley has been undocked.
Swivel the two handles up (item 1 in fig. 6.14 - 2).
6
Fig. 6.14 - 2 Component trolley - swivel handles up to push
6
With both hands on the handles, pull the component trolley out of the machine.
User Manual SIPLACE CA-Series 6 Working with the Machine
From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.14 Docking/Undocking the Component Trolley
389
6
6.14.3 Docking the X-Series Component Trolley
6
Fig. 6.14 - 3 Component trolley and COT insert, SIPLACE X-Series
(1) Component trolley docking unit, SIPLACE X-Series
(2) Component trolley, SIPLACE X-Series
(3) Locking latches
WARNING
Observe the safety instructions for moving the component trolley in section 2.6.7,
page 76
.
6 Working with the Machine User Manual SIPLACE CA-Series
6.14 Docking/Undocking the Component Trolley From software version SC.708.0 Edition 12/2014 EN -DRAFT
390
6
6
6
Carefully push the component trolley into machine as far as the stop.
6
Press the appropriate button on the input or output side of the machine (item 1, 2, 3 or 4 in
fig. 6.14 - 1
) until the component trolley has been undocked.
Push the sleeve (item 1 in fig. 6.14 - 4) on both handles up and swivel the handle down (item
2 in fig. 6.14 - 4
).
CAUTION
Pushing in component trolley!
Only dock the component trolley onto the COT insert designed for it.
When pushing in the component trolley for the SIPLACE X-Series into the machine,
make sure that you do not hit the locking latches (item 3 in fig. 6.14 - 3
) against any
obstacles.
PLEASE NOTE
Cut tapes flush
If you do not cut tapes off flush at the front end of the X feeder modules, the emptied tapes
will not enter the empty tape duct.
Cut the tapes off flush, before you dock the X-Series component trolley.
CAUTION
Position of placement head!
Check that the placement head is outside the range of the component trolley.
PLEASE NOTE
Docking only possible if protective cover is closed
Close the protective covers.