00197498-03_UM_SiplaceCA-Serie_EN.pdf - 第307页

User Manual SIPLACE CA-Series 5 Setting up and Commissioning From software version SC.708.0 Edition 12/20 14 EN -DRAFT 5.5 Setting Up the Placement Machine 307 5.5.10.5 Fitting the Ground Cable for the Doors  Fasten the…

100%1 / 518
5 Setting up and Commissioning User Manual SIPLACE CA-Series
5.5 Setting Up the Placement Machine From software version SC.708.0 Edition 12/2014 EN -DRAFT
306
Insert the mandrel (item 5 in fig. 5.5 - 15) for the transportation cover into the hole (item 6 in
fig. 5.5 - 15
) for the second half of the extension kit.
Position the second half of the extension kit so that the assembly bracket lies on the assembly
bar (item 7 in fig. 5.5 - 14
).
Fasten this second half of the placement machine with 2 fillister head screws M6x16 and the
corresponding washer (item 3 in fig. 5.5 - 14
).
5.5.10.3 Fastening the Hexagonal Shaft Guidance
When using a single conveyor, fasten one guidance for the hexagonal shaft (item 8 in fig. 5.5
- 13) to the extension kit with two fillister head screws M6x16 and washers
When using a dual conveyor, fasten two guidances for the hexagonal shaft (item 8 in fig. 5.5
- 13) to the extension kit with two fillister head screws M6x16 and washers.
5.5.10.4 Establishing Cable Connections - Extension Kit on the PCB Input Side
5
Left side of extension kit
(viewed in direction of transport)
Connector/cable To connector/
cable
Start/Stop button
Switch, PCB conveyor cover
X61/03020410 X61/03002537
Protective cover switch, location 4 X54/03020409 X54/03002540
Button for the COT insert, location 4 X242/03021056 X242/03021054
Right side of extension kit
(viewed in direction of transport)
Connector/cable To connector/
cable
EMERGENCY STOP button
Start/Stop button
X64/03020687 X64/03002538
Protective cover switch, location 1 X51/03020409 X51/03002539
Button for the COT insert, location 1 X212/03021056 X212/03021051
User Manual SIPLACE CA-Series 5 Setting up and Commissioning
From software version SC.708.0 Edition 12/2014 EN -DRAFT 5.5 Setting Up the Placement Machine
307
5.5.10.5 Fitting the Ground Cable for the Doors
Fasten the two ground cables for the doors (item 4 in fig. 5.5 - 14) to the machine frame as
follows:
5
Fig. 5.5 - 16 Fitting the ground cable
5.5.10.6 Checking and Setting the Protective Cover Switch
Check the function of the protective cover switch (item 7 in fig. 5.5 - 15, page 294).
Adjust the protective cover switch if necessary (see service manual).
5
Hex nut M
Spring washer M, DIN 7980
Washer M, DIN 125
Cable lug, annular
Contact washer
5 Setting up and Commissioning User Manual SIPLACE CA-Series
5.5 Setting Up the Placement Machine From software version SC.708.0 Edition 12/2014 EN -DRAFT
308
5.5.10.7 Installing the Bottom Hand Guard
The CA-Series placement machines are only supplied with one "bottom" hand guard. However, if
the placement machines are installed in a line, there will be no hand guard between neighboring
output and input conveyors.
5
5
Fig. 5.5 - 17 Fitting the "bottom" hand guard on the PCB input side
(1) "Bottom" hand guard [03003432-01]
5.5.11 Installing the Box PC Unit on the CA4 i
The SIPLACE CA-Series placement machines can be fitted once with the box PC unit or with a
computer unit. Section 5.5.11
describes installation of the box PC. For a description of how to in-
stall the computer unit, refer to section 5.5.12
, page 314.
WARNING
Unauthorized access by personnel!
A missing hand guard between the input and output sides of the placement machine in a
production line could lead to unauthorized access if staff reach into the inside of the place-
ment machine.
Always fit the bottom hand guard at the input side of the first placement machine and
on the output side of the last placement machine in a line [03003432-01] with 4 hexa-
gon socket-head screws M4x12.