00197498-03_UM_SiplaceCA-Serie_EN.pdf - 第364页
6 Working with the Machine User Manual SIPLACE CA-Series 6.6 Performing a Sight Check From software version SC.708.0 Edition 12/2014 EN -DR AFT 364 6.6 Performing a Sight Check 6.6.1 Checking the Feeders (X-Series) 6 Fig…
User Manual SIPLACE CA-Series 6 Working with the Machine
From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.5 Shift Changeover
363
6.5 Shift Changeover
Splice the tapes early. The feeder modules do not have to be refilled as soon as the new shift
starts. This minimizes extended down times.
At the shift change, pass important information on to the next operator. This includes, for in-
stance, changes to the placement program. Also read through the list of the descriptions of
the steps to take in section 6.10
.
Perform a setup check.
Make sure that the feeder modules are equipped with the correct components, that they are
at the correct locations in the component trolley and that the conveyor increment is set cor-
rectly.
SWS:
Check that the tools on the flip head are seated correctly (see section 6.4.6 on page 362) and
then check those on the die attach head, if required. Remove any components from the ma-
chine. Check whether the correct multiple needle kit has been fitted (see section 6.4.5 on
page 358). Remove any flux from the LDU and clean the LDU thoroughly with alcohol, using
the clean cycle. For more details, see the SIPLACE LDU-X User Manual (item number of Ger-
man version [00196057-xx]).
6
PLEASE NOTE
Clean line at transfer
At the end of your shift, transfer the line in the state that you would like to find it in when
you begin your shift, meaning:
– The reject bins (also for SWS) are empty (see section 6.4.7 on page 362).
– The waste tape containers are empty.
– The feeding areas are carefully cleaned with a vacuum cleaner.
6 Working with the Machine User Manual SIPLACE CA-Series
6.6 Performing a Sight Check From software version SC.708.0 Edition 12/2014 EN -DRAFT
364
6.6 Performing a Sight Check
6.6.1 Checking the Feeders (X-Series)
6
Fig. 6.6 - 1 Checking the X feeder modules
(1) Flap
(2) Blade
(3) Status display
(4) LCD display
6
Check to see whether the tape foil removal container for the X tape feeder module is full.
Open the flap (item 1). Pull out the cover foil and cut it with scissors or on the integral blade
(item 2) on 8 and 12 mm X tape feeder modules.
User Manual SIPLACE CA-Series 6 Working with the Machine
From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.6 Performing a Sight Check
365
6
Check the multicolor status display (item 3 in fig. 6.6 - 1).
– If it lights up green, the feeder module is on standby.
– If it lights up orange, it is signaling a warning. The text of the warning appears on the LCD
display (item 4 in fig. 6.6 - 1
).
– If the status display lights up red, a malfunction has occurred. The error message
appears on the LCD display (item 3 in fig. 6.6 - 1
).
A list of the LCD and status displays on the operator panel is given in section 6.9
, page
379
. 6
If the status display is off, the cause may be as follows: 6
– The feeder module is not in the current setup.
– The feeder module is defective.
– The feeder module has been disabled (due to a drop in pressure, for example)
6.6.2 Splicing the Tapes in Good Time
6
6
CAUTION
Problems with cover foil withdrawal!
If the cover foil tears, this could lead to problems with the cover foil withdrawal.
There is an integral blade (item 2) for easily cutting the on the 8 and 12 mm X tape feeder
modules.
PLEASE NOTE
Late splicing of tapes
Late splicing of tapes could lead to prolonged down times..
Splice the tapes early enough so that the feeder modules do not run out of compo-
nents.
PLEASE NOTE
Early splicing of tapes
Early splicing of tapes can have the following consequence: when the old tape is rolled
up onto the new reel, the new reel could become too full and the tape will slide off it and
get caught up. This will again result in pick-up errors and prolonged down times.
Splice the tapes at the right time so that the old and new tapes do not get caught.