00197498-03_UM_SiplaceCA-Serie_EN.pdf - 第381页

User Manual SIPLACE CA-Series 6 Working with the Machine From software version SC.708.0 Edition 12/20 14 EN -DRA FT 6.9 LCD and Status Displays on the X Feeder Module 381 6 6 Foil Jam (Foil jam) Red Foil motor has locked…

6 Working with the Machine User Manual SIPLACE CA-Series

6.9 LCD and Status Displays on the X Feeder Module From software version SC.708.0 Edition 12/2014 EN -DRAFT

380

6.9.1 Warnings

6.9.2 Error Messages and Troubleshooting

Text on the

LCD display

Status

display

Meaning Solution

Remove Foil

(Remove the foil)

Orange The selected function is not

permitted when the cover foil

is tensioned (foil rocker is

pressed down).

If you wish to carry out that function, remove

the foil from the pair of gear wheels and cut

it off to relieve the pressure on the foil rocker.

Text on the

LCD display

Status

display

Meaning Solution

None Red,

flashing

Feeder module software not

jumping to the application

Reload the application software

Load feeder module software

Handle --->>

(Handle --->>)

Red Feeder module was sig-

naled, but removal handle is

not yet pushed in

Push in the removal handle

Low Voltage

(Low voltage)

Orange 24V supply voltage did not

rise above the switch-on

threshold after switching on

Check the power supply

Low Voltage

(Low voltage)

Red 24V supply voltage rose

above the switch-on thresh-

old after switching on and

was then interrupted

Check the power supply

Feed Timeout

TransTimeout

(Timeout in tape

feeder cycle)

Red Tape feeder cycle did not

end correctly within the spec-

ified time (timeout for the

"Feed" function)

Is the tape reel jammed in the container?

Is there a component jammed in the pick-up

area between component tape and compo-

nent window?

Once the obstacle has been eliminated, use

the arrow keys to restart the conveyor. The

feeder module will move the defective con-

veyor to the end, and then returned to its

position

Foil Torn

(Foil torn)

Red Foil was not tensioned within

the specified time

The foil is probably torn. Insert new foil and

tension

Foil PeelErr

(Error while peel-

ing off the foil)

Red Foil was not peeled off even

though the tape is moved

The cover foil is probably jammed beneath

the pick-up window and cannot be peeled

off correctly

User Manual SIPLACE CA-Series 6 Working with the Machine

From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.9 LCD and Status Displays on the X Feeder Module

381

Foil Jam

(Foil jam)

Red Foil motor has locked up Leveling gears blocked by foil? => Remove

the foil

EEP-WriteErr

(Error while back-

ing up data in the

EEPROM)

Red The data back-up in the EE-

PROM was not carried out

correctly

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pick-up window).

Press the SET button to confirm the error.

Then press the yellow button to confirm the

reference run prompt.

EEP-ReadErr

(Error while read-

ing the

EEPROMS)

Red Data was not read from the

EEPROM correctly

EEP-DataErr

(Error while back-

ing up the data in

the EEPROM)

Red The data back-up in the EE-

PROM was not carried out

fully

Reference o

Red Position information is no

longer available for the com-

ponent tape drive

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pick-up window).

Then press the "FOIL" button to start the

reference run.

CAN BusError

(CAN bus error)

Red CAN bus error Log off and on again, check the optical fiber

interface

ParNotSaved! Red Parameters were not saved Default parameters are loaded automatical-

ly, i.e. the most recent operator settings are

overwritten -> The settings (e.g. increment)

will have to be made again. Replace the

control board if this error occurs frequently.

ParWrongSave Red Wrong or incomplete param-

eters were saved

BootFlashErr

FlashDataErr

Red Can no longer write to boot

or application memory cor-

rectly

Replace the feeder module or control board

PLEASE NOTE

 Remove the component tape before a reference run.

Text on the

LCD display

Status

display

Meaning Solution

6 Working with the Machine User Manual SIPLACE CA-Series

6.10 Changing the Setup From software version SC.708.0 Edition 12/2014 EN -DRAFT

382

6.10 Changing the Setup

6.10.1 Changing the Setup on the Placement Machine

6.10.1.1 Printing Out Conversion Instructions Before Changing the Setup

Before a change of setup, print out the conversion instructions on the printer for the SIPLACE Pro

computer as described in the "SIPLACE Pro" manual or in the online help.

6.10.1.2 Important Points When Changing the Feeder Modules

 Handle the feeder modules carefully when you insert them into or remove them from the

changeover table. Make sure that the X feeder modules do not bump against the centering

bar (see item 5 in fig. 6.7 - 3

, page 373) of the changeover table.

 Vacuum the supporting surfaces of the feeder modules and clean the surface of the compo-

nent feeder table when necessary according to the instructions in the Preventive Mainte-

nance Manual.

 Remove loose components using a brush or a vacuum cleaner with a suitable nozzle.

CAUTION

Risk of injuries!

Fine metal splinters from components could injure hands.

 Avoid removing components from the changeover table with your fingers.