00197498-03_UM_SiplaceCA-Serie_EN.pdf - 第302页

5 Setting up and Commissioning User Manual SIPLACE CA-Series 5.5 Setting Up the Placement Machine From software version SC.708.0 Edition 12/2014 EN -DR AFT 302  Dismantle the cable covers (item 3 and 5 in fig. 5.5 - 13 …

100%1 / 518
User Manual SIPLACE CA-Series 5 Setting up and Commissioning
From software version SC.708.0 Edition 12/2014 EN -DRAFT 5.5 Setting Up the Placement Machine
301
5.5.9 Fitting the Input Conveyor
5.5.9.1 Tools
– Allen keys, DIN 911, set
– Phillips screwdriver, size 1
5.5.9.2 Assembly
5
Fig. 5.5 - 13 Input conveyor - dual conveyor
(1) Side panel, input conveyor
(2) Side panel, processing conveyor 1
(3) Cable cover 20 x 200
(4) Countersunk screw, ISO 7046, M3x6, 2x per cable cover
(5) Cable cover 20 x 310
(6) Fillister head screw DIN 912, M3x5, 1x per cable cover
(7) Fillister head screw DIN 912, M6x16, and washer, 4 per panel
(8) Hexagonal shaft guidance
(9) Hexagonal shaft (single conveyor: one, dual conveyor: two)
(10) Drive unit
5 Setting up and Commissioning User Manual SIPLACE CA-Series
5.5 Setting Up the Placement Machine From software version SC.708.0 Edition 12/2014 EN -DRAFT
302
Dismantle the cable covers (item 3 and 5 in fig. 5.5 - 13) on the input conveyor (item 1 in fig.
5.5 - 13
).
Place the side (item 1 in fig. 5.5 - 13) carefully against the side of the processing conveyor
(item 2 in fig. 5.5 - 13
).
5
Fasten each side with 4 fillister head screws M6x16 and the corresponding discs (item 7 in
fig. 5.5 - 13
).
Connect the power cable to the light barriers and drive motors.
Fasten the cable covers (item 3 and 5 in fig. 5.5 - 13).
Insert the hexagonal shaft (item 9 in fig. 5.5 - 13) into the drive unit (item 10 in fig. 5.5 - 13).
Make sure that the hexagonal shaft guidance (item 8 in fig. 5.5 - 13) always points to the con-
veyor side to which the drive unit (item 10 in fig. 5.5 - 13
) is fixed.
CAUTION
Be careful not to cut through any of the light barrier or drive motor cables.
User Manual SIPLACE CA-Series 5 Setting up and Commissioning
From software version SC.708.0 Edition 12/2014 EN -DRAFT 5.5 Setting Up the Placement Machine
303
5.5.10 Fitting the Extension Kit to the PCB Input Side
5.5.10.1 Tools
– Allen keys, DIN 911, set
– Machine key
5.5.10.2 Assembly
5
Fig. 5.5 - 14 Fitting the extension kit to the PCB input side
(1) Extension kit, dismantled
(2) Door
(3) Fillister head screw DIN 912, M6x16 and washer
(4) Grounding connection
(5) Transport cover
(6) Side plate, dismantled
(7) Insert rail
(8) Computer unit or box PB unit (see section 5.5.11
, page 308)
(9) Axis unit (CA4)