YRM20_Ope_E.pdf - 第217页

A2. Y AMAHA Service website for user A-2 Appendix A2. Y AMAHA Ser vice website for user Our service information can be obtained through the Service W ebsite. The following contents can be available for example. Item Cont…

A1. Speciﬁcations

A-1

Appendix

A1. Specifications

█

YRM20 specifications

Item Specifications

Operating ambient temperature

Function guaranteed: 15 to 35°C

Accuracy guaranteed: 20 to 28°C

Operating ambient humidity 20 to 80% (no condensation), optimal range: 50 to 60%

Noise level Under 78dB

Power requirement (voltage and frequency) 3-phase AC 200/208/220/240/380/400/416V +/- 10%, 50/60Hz

Power capacity 2.5kVA (Peak 5.4kVA) *

Breaker rating 30A*

Maximum current

55A*

Average power consumption

2.2kW

Power cable (conductor cross-section area) 6mm

or more

Overvoltage category *

Category III

Pollution degree *

Degree 2

Supply air pressure *

0.45MPa or more

Air consumption (ANR) *

RM • RM type : 60L/min (average); 270L/min (max.)*

HM • HM type : 260L/min (average); 320L/min (max.)*

FM • FM type : 160L/min (average); 270L/min (max.)*

Altitude 1000m or less above sea level

Board transport height *

900mm +/-10mm

Data

Number of mounting points *

32400 points

Number of component types 255 types per board

Number of fiducial marks *

128 sets per board

Board data capacity per one machine 500MB

*1: Conforms to IEC60664-1.

*2: This value is different from the air pressure setting of the machine(0.40MPa). Please supply clean and dry air treated with an air

dryer and air filter.

*3: Distance from the floor surface to the upper surface of conveyor belt.

*4: Decreases with the number of boards, blocks and fiducial marks.

*5: When using 2-point fiducial mode.

*6: Is a flow volume under condition of; Temperture: 20˚C, Relative humidity: 65%, Absolute pressure: 101.3kPa (1.03kgf/cm

760mmHg).

*7: When X and Y axes move at full speed.

*8: Includes the inrush current of the transformer.

*9: When 200V power is supplied.

*10: If the machine is equipped with eATS30 (option), add the air consumption of 30 L/min for each.

NOTE

See speciﬁcation sheets for more detailed information not listed above.

A2. YAMAHA Service website for user

A-2

Appendix

A2. YAMAHA Service website for user

Our service information can be obtained through the Service Website. The following contents can be

available for example.

Item Contents

Important notification New/corrected service information

Manual download Download the operation/maintenance manuals

Support items Introduction of the list of maintenance tools, etc.

Training Informations about periodical training schedule

Vision recognition Recognition information of special parts such as coils

Troubleshooting Supporting informations for trouble solutions

Circuit/air path diagram Materials for investigation about the electrical troubles

Maintenance parts list List of maintenance target parts

NOTE

The user registration is necessary for using our Service website. The electronic certiﬁcation and the ﬁrst time password are

provided upon completing your registration.

Contact your sales representative for the detail of user registration.

Index

S-1

Index

Safety instructions

Cautions during power outage xiii

CE marking i

Deﬁning the operator and service personnel xi

Handling batteries xvii

Handling grease and oil xvii

Handling heavy objects xviii

Handling solvents xvi

Handling the laser xvi

Label positions iv

Lock out the main switch and the air supply/

exhaust switch xii

Safety x

Safety message in this manual xix

Warning labels ii

Adjusting board hold plate position 3-15

Air connection port 1-3

Axis 2-21,2-22

[Axis] button 2-19

Axis conﬁguration 1-62

X/Y axis and conveyor axis conﬁguration 1-64

Before operation 2-1

Block Skip function

[Block Skip] button 2-16,3-32

Blow station 1-22

[Board Clamp] button 2-20

Board clamping method 3-10

Board position in machine by conveyor type/

board size 1-57

Buttons and parameter input boxes 2-12

Buzzer 1-4

Carriage clamp switch 1-7

Changing conveyor width 3-11

Check cleanness on nozzle tips 3-23

Checking condition of clamping the board

3-19

Clearing an error 2-2

Component supply section 1-33

Component tape feed pitch 2-64

Conﬁrming nozzles 3-22

Connection between machines 1-4

[Convey Board] button 2-18

Conveyor unit 1-53

Conveyor unit setup 3-10

[Convey-out Stop] button 2-15,3-27

[Current Nozzles] button 2-21,2-22

[Cycle Stop] button 2-15,3-27

Detaching component tape 2-72

Displaying the production monitors 2-25

Disposing of used carrier tape 2-68

Disposing of used cover tape 2-66

Edge clamp 3-10

Emergency stop

Canceling emergency stop 2-1

Empty tape dust box 2-68

Ending production 3-27

[Entrance Stopper] button 2-20

Error screen 2-13

[Exit Stopper] button 2-20

Feeder exchange carriage 1-35

[Feeder Information] button 2-23

Feeder removing conditions 1-48

Feeder set position

Power connector 1-37

Flow from starting up machine to production

3-1

Head unit 1-10

HM Head unit 1-13

RM Head unit 1-11

Head unit axis conﬁguration 1-62

How to check the sensor addresses 1-56

Input/output signals between machines 1-4

Keyboard 1-8

Laying out push-up pins 3-11

[Machine] button ,1-28

Machine layout 1-33

Machine main unit 1-1

Main menu button area 2-10

Main stopper 3-12

[Main Stopper] button 2-20,3-12

Main switch 1-2,3-3

Manual conveyor operation 2-17

Manual feeder operation 2-23

Manual head operation 2-21

Manual I/O operation 2-24

Monitor

Alignment screen 2-32

Fiducial screen 2-34

Nozzle health check screen 2-44

Pick Pos. 2-36

Pick Rate Warning screen 2-38,2-39

Schedule task screen 2-42

Vision screen 2-29

[Monitor] button 2-25

Multi-view camera 1-61

Non-stop feeder change 1-46

[Nozzle Change] button 2-21,2-22

Nozzle health check 2-44

Nozzle shaft blow

Automatic nozzle shaft blow procedure 1-28

Manual nozzle shaft blow procedure 1-23

Nozzle station 1-16

Nozzle types 1-14

[Off] button 3-28

One-stop cover 1-45

Operation panel and data input unit 1-5

Operation panel buttons

[ACTIVE] button 1-7

[EMERGENCY STOP] button ,1-7

[ERROR CLEAR] button 1-7

[READY] button 1-7

[RESET] button 1-7

[START] button 1-7

[STOP] button 1-7

Operation screen 2-10

[Operator] button 3-5

[Origin] button 2-15

Password 3-6

Pick Rate Warning 2-38

Pickup position offset 2-36

Powering off the machine 3-28

Pre-operation check 3-2

Preparing component tape 2-47,3-21

Pressing [Feeder Remove] button 1-49

Pressure gauge 1-3

[Push Up] button 2-20,3-12

Recognition unit 1-58

Fiducial camera 1-59

Scan camera 1-59

Side-view camera 1-59

[Required Nozzles] button 2-15,3-22

[Required Parts] button 2-15,3-21

[Required Parts] screen 3-21

Resuming operation from the stopped point

3-30

[Halfway Continue] button 2-15,3-30

Return-to-origin 3-4