YRM20_Ope_E.pdf - 第23页

General Contents EPKMX-208-0100 General Contents About this manual 1. Using this manual i 1.1 Contents of each chapter ii 1.2 Page layout iii Chapter 1 Unit names and functions 1. Machine main unit 1-1 2. Operation panel…

100%1 / 220
5. Safety message in this manual
xix
Safety instructions
5. Safety message in this manual
The contents that must be followed to prevent users and third parties from injury and damage to a
machine are explained as "Warning" and "Caution" in this manual. The contents that are required and
helpful information when operating a machine are explained as "Note" and "Tip".
►
Warning
w
WARNING
INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS
INJURY. THESE ARE POINTS MOST ESSENTIAL FOR PROTECTING THE SAFETY OF THE MACHINE OPERATOR, INSPECTOR
AND SERVICE PERSONNEL.
►
Caution
c
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury, or material loss or damage to
the machine. These points are important for protecting the safety of the machine and data, etc.
►
Note
n
NOTE
Provides required information when operating a machine in a simple and clear manner.
►
Tip
TIP
Provides helpful explanation for work.
►
Emergency stop
e
IF THIS MARK IS IN THIS MANUAL, MAKE SURE TO WORK WHILE A MACHINE IS IN EMERGENCY
STOP.
General Contents
EPKMX-208-0100
General Contents
About this manual
1. Using this manual i
1.1 Contents of each chapter ii
1.2 Page layout iii
Chapter 1 Unit names and functions
1. Machine main unit 1-1
2. Operation panel and data input unit 1-5
2.1 Operation display screen/Operation button 1-6
2.2 Keyboard (option) 1-8
2.3 Other connection ports 1-9
3. Head unit 1-10
3.1 Component pick-and-place head 1-11
3.1.1 RM Head unit 1-11
3.1.2 HM Head unit 1-13
3.2 Nozzle types 1-14
3.3 Nozzle station (option) 1-16
3.3.1 Overview of Nozzle station 1-16
3.3.2 Nozzle holder 1 and 2 1-17
3.3.3 Type A nozzle holder 1-18
3.3.4 Type B nozzle holder 1-19
3.3.5 Attaching/Detaching nozzle holder 1-20
3.4 Blow station 1-22
3.4.1 Shaft-blow function 1-22
3.4.2 Manual nozzle shaft blow procedure 1-23
3.4.3 Automatic nozzle shaft blow procedure 1-28
3.4.4 Shaft blow dump of very small components 1-31
3.5 Vacuum pump ( RM head) 1-32
3.5.1 Vacuum pump (RM head) 1-32
4. Component supply section 1-33
4.1 Machine layout 1-33
4.2 Supplying component tape 1-35
4.2.1 Feeder exchange carriage 1-35
4.2.2 Feeder exchange carriage attaching section of machine 1-38
4.2.3 Attaching/Detaching upper cover 1-41
4.3 One-stop cover (option) 1-45
4.4 Non-stop feeder change 1-46
Feeder removing conditions : 1. Setting "Skip Retry" 1-48
Feeder removing conditions : 2. Pressing [Feeder Remove] button 1-49
Feeder removing conditions : 3. Setting alternative component function 1-50
General Contents
5. Conveyor 1-53
5.1
Conveyor unit 1-53
5.2 Sensor layout of conveyor unit 1-55
5.3 Board position in machine by board size 1-57
6. Recognition unit 1-58
6.1 Fiducial, Scan and Side-view camera 1-58
6.2 Side-view function (Scan camera / Side-view camera) 1-60
6.3 Multi-view cameras 1-61
7. Axis configuration 1-62
7.1 Head unit axis configuration 1-62
7.1.1 RM head unit 1-62
7.1.2 HM head unit 1-63
7.2 Main axis and conveyor axis configuration 1-64
Chapter 2 Basic operation
1. Before operation 2-1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-2
1.3 Typical errors and troubleshooting 2-3
1.4 Switching the display language 2-8
2. Operation screen and buttons 2-10
2.1 Basic configuration of operation screen 2-10
2.2 Setup screen 2-15
2.3 Unit screen 2-17
3. Displaying the production monitors 2-25
3.1 Production 2-25
3.2 Main 2-27
3.3 Vision 2-29
3.4 Alignment 2-32
3.5 Retry 2-33
3.6 Fiducial 2-34
3.7 Badmark 2-35
3.8 Pick Pos. (Pickup position offset) 2-36
3.9 Pick Rate Warning 2-38
3.10 Schedule task 2-42
3.11 Nozzle health check 2-44
3.12 Gap of pick-up position 2-46