YRM20_Ope_E.pdf - 第218页

Index S-1 Index Index Safety instructions Cautions during power outage xiii CE marking i Deﬁning the operator and service personnel xi Handling batteries xvii Handling grease and oil xvii Handling heavy objects xviii Han…

A2. YAMAHA Service website for user

A-2

Appendix

A2. YAMAHA Service website for user

Our service information can be obtained through the Service Website. The following contents can be

available for example.

Item Contents

Important notification New/corrected service information

Manual download Download the operation/maintenance manuals

Support items Introduction of the list of maintenance tools, etc.

Training Informations about periodical training schedule

Vision recognition Recognition information of special parts such as coils

Troubleshooting Supporting informations for trouble solutions

Circuit/air path diagram Materials for investigation about the electrical troubles

Maintenance parts list List of maintenance target parts

NOTE

The user registration is necessary for using our Service website. The electronic certiﬁcation and the ﬁrst time password are

provided upon completing your registration.

Contact your sales representative for the detail of user registration.

Index

S-1

Index

Safety instructions

Cautions during power outage xiii

CE marking i

Deﬁning the operator and service personnel xi

Handling batteries xvii

Handling grease and oil xvii

Handling heavy objects xviii

Handling solvents xvi

Handling the laser xvi

Label positions iv

Lock out the main switch and the air supply/

exhaust switch xii

Safety x

Safety message in this manual xix

Warning labels ii

Adjusting board hold plate position 3-15

Air connection port 1-3

Axis 2-21,2-22

[Axis] button 2-19

Axis conﬁguration 1-62

X/Y axis and conveyor axis conﬁguration 1-64

Before operation 2-1

Block Skip function

[Block Skip] button 2-16,3-32

Blow station 1-22

[Board Clamp] button 2-20

Board clamping method 3-10

Board position in machine by conveyor type/

board size 1-57

Buttons and parameter input boxes 2-12

Buzzer 1-4

Carriage clamp switch 1-7

Changing conveyor width 3-11

Check cleanness on nozzle tips 3-23

Checking condition of clamping the board

3-19

Clearing an error 2-2

Component supply section 1-33

Component tape feed pitch 2-64

Conﬁrming nozzles 3-22

Connection between machines 1-4

[Convey Board] button 2-18

Conveyor unit 1-53

Conveyor unit setup 3-10

[Convey-out Stop] button 2-15,3-27

[Current Nozzles] button 2-21,2-22

[Cycle Stop] button 2-15,3-27

Detaching component tape 2-72

Displaying the production monitors 2-25

Disposing of used carrier tape 2-68

Disposing of used cover tape 2-66

Edge clamp 3-10

Emergency stop

Canceling emergency stop 2-1

Empty tape dust box 2-68

Ending production 3-27

[Entrance Stopper] button 2-20

Error screen 2-13

[Exit Stopper] button 2-20

Feeder exchange carriage 1-35

[Feeder Information] button 2-23

Feeder removing conditions 1-48

Feeder set position

Power connector 1-37

Flow from starting up machine to production

3-1

Head unit 1-10

HM Head unit 1-13

RM Head unit 1-11

Head unit axis conﬁguration 1-62

How to check the sensor addresses 1-56

Input/output signals between machines 1-4

Keyboard 1-8

Laying out push-up pins 3-11

[Machine] button ,1-28

Machine layout 1-33

Machine main unit 1-1

Main menu button area 2-10

Main stopper 3-12

[Main Stopper] button 2-20,3-12

Main switch 1-2,3-3

Manual conveyor operation 2-17

Manual feeder operation 2-23

Manual head operation 2-21

Manual I/O operation 2-24

Monitor

Alignment screen 2-32

Fiducial screen 2-34

Nozzle health check screen 2-44

Pick Pos. 2-36

Pick Rate Warning screen 2-38,2-39

Schedule task screen 2-42

Vision screen 2-29

[Monitor] button 2-25

Multi-view camera 1-61

Non-stop feeder change 1-46

[Nozzle Change] button 2-21,2-22

Nozzle health check 2-44

Nozzle shaft blow

Automatic nozzle shaft blow procedure 1-28

Manual nozzle shaft blow procedure 1-23

Nozzle station 1-16

Nozzle types 1-14

[Off] button 3-28

One-stop cover 1-45

Operation panel and data input unit 1-5

Operation panel buttons

[ACTIVE] button 1-7

[EMERGENCY STOP] button ,1-7

[ERROR CLEAR] button 1-7

[READY] button 1-7

[RESET] button 1-7

[START] button 1-7

[STOP] button 1-7

Operation screen 2-10

[Operator] button 3-5

[Origin] button 2-15

Password 3-6

Pick Rate Warning 2-38

Pickup position offset 2-36

Powering off the machine 3-28

Pre-operation check 3-2

Preparing component tape 2-47,3-21

Pressing [Feeder Remove] button 1-49

Pressure gauge 1-3

[Push Up] button 2-20,3-12

Recognition unit 1-58

Fiducial camera 1-59

Scan camera 1-59

Side-view camera 1-59

[Required Nozzles] button 2-15,3-22

[Required Parts] button 2-15,3-21

[Required Parts] screen 3-21

Resuming operation from the stopped point

3-30

[Halfway Continue] button 2-15,3-30

Return-to-origin 3-4

Index

S-2

Index

Safety cover 1-2

Schedule Speciﬁcation 1-28

Schedule task 2-42

Selecting the board data 3-9

Selecting the operator 3-5

Sensor layout of conveyor unit 1-55

[Sensor Tune] button 2-17

Set air pressure 1-3

Setting alternative component function 1-50

Setting component tape 2-47

Setting feeders on the feeder exchange

carriage 2-57

Setting "Skip Retry" 1-48

Setting the Nozzle Tip Cleanliness Check

3-24

Setting the operation speed 3-26

Setup screen 2-15

Set-up station 1-2

Side-view function 1-60

Signal light 1-4,3-3

Starting production 3-26

Starting the machine 3-3

Status area 2-10

[STOP] button 3-27

Submenu button and parameter area 2-10

[Tip Cln Check] button 2-15,3-23

[TrayCnt] button 2-15

Typical errors 2-3

Unit screen 2-17

Upper cover 1-39

Attaching upper cover 1-42

Detaching upper cover 1-41

Temporary placing of upper cover 1-43

USB ﬂash drive port 1-9

Vacuum pump ( RM head) 1-32

Warm-up 3-7

[Warm Up] button 2-15,3-7

Watch-and-wait mode 2-41

[Width] button 2-15,2-18

Working Ratio 2-28