YRM20_Ope_E.pdf - 第97页
4. Preparing component t ape 2-47 4.1 T ape fe eders 2-47 4.1 .1 Se tting component tape on t he feeder 2- 47 4.1 .2 Set ting feeders on the feeder exchange carriage 2 -57 4.1 .3 At taching the feeder exchange carriage o…
Chapter 2 Basic operation
Contents
1. Before operation 2-1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-2
1.3 Typical errors and troubleshooting 2-3
1.4 Switching the display language 2-8
2. Operation screen and buttons 2-10
2.1 Basic configuration of operation screen 2-10
2.2 Setup screen 2-15
2.3 Unit screen 2-17
3. Displaying the production monitors 2-25
3.1 Production 2-25
3.2 Main 2-27
3.3 Vision 2-29
3.4 Alignment 2-32
3.5 Retry 2-33
3.6 Fiducial 2-34
3.7 Badmark 2-35
3.8 Pick Pos. (Pickup position offset) 2-36
3.9 Pick Rate Warning 2-38
3.10 Schedule task 2-42
3.11 Nozzle health check 2-44
3.12 Gap of pick-up position 2-46
4. Preparing component tape 2-47
4.1 Tape feeders 2-47
4.1.1 Setting component tape on the feeder 2-47
4.1.2 Setting feeders on the feeder exchange carriage 2-57
4.1.3 Attaching the feeder exchange carriage on the mounter 2-61
4.1.4 Setting board data of component tape 2-64
4.1.5 Disposing of used cover tape and carrier tape 2-66
4.1.6 Detaching the feeder exchange carriage 2-69
4.1.7 Detaching feeder from the feeder exchange carriage 2-71
4.1.8 Detaching component tape from feeder 2-72
4.2 SS Feeder 2-75
4.2.1 Setting SS feeder on the feeder exchange carriage 2-76
4.2.2 Attaching the feeder exchange carriage on the mounter 2-78
4.2.3 Detaching the feeder exchange carriage from mounter 2-80
4.2.4 Detaching SS feeder from carriage 2-82
1. Before operation
2-1
Chapter 2 Basic operation
1. Before operation
The following explains how to cancel emergency stop and clear errors. Read before operating the
machine.
█
Cautions during machine operation
• Do not turn off the compressed air during operation. The machine may malfunction, as pneumatic
devices are not correctly controlled.
• Before beginning maintenance, switch off the air-supply as needed. Before that, if there is the
residual pressure releasing valve, make sure to open it to release the residual pressure.
█
Cautions during power outages
If a power outage (blackout) occurs during automatic machine operation, always turn the main power
switch off to prevent faulty operation or machine damage after power has been restored. Also remove
the boards that remain in the machine.
1.1 Canceling emergency stop
Follow these steps to cancel emergency stop.
1
Release the emergency stop button.
When the emergency stop button is pressed, turn it clockwise to release it.
2
Check safety.
Before continuing the procedure, check the surrounding area for safety.
3
Press the [READY] button.
Pressing the [READY] button on the operation panel turns on the servomotors.
c
CAUTION
The [READY] button is enabled only when the [ACTIVE] button next to it is active.
[READY] button
Operation display
Emergency stop button
[READY] button
23200-KMX-00
4
Check the signal light and screen display.
Check that the red lamp of the signal light is off and the emergency stop sign on the top left (status
area) of the operation screen is now off.