YSP_Users_E.pdf - 第204页

6-20 6 Other functions 4.2 [Unit] - [Conveyor] tab screen T he [Unit] - [Conveyor] tab screen allo ws you to manually operate eac h conveyor unit and c heck the status of the convey or sensors and I/O signals on the grap…

6-19

Other functions

Manual axis movement

This section describes how to use the buttons on the "Move Axis" screen, using the [SY/SZ] tab as an example.

"Move Axis" screen

[SY/SZ] tab

64618-L3-10

1. SY-axis movement buttons, [PTP] button, [Brake] button

Pressing the arrow buttons moves the squeegee head in the Y direction. When the [Step Mode] button is in the depressed

state, the squeegee head moves at the specified step stroke each time the arrow buttons are pressed.

Pressing the [PTP] button displays the "PTP" dialog box. You can directly specify the position where you want to move the

squeegee head. The current position is displayed in the "SY (mm)" box.

The [Brake] button turns the SY-axis brake on or off.

2. SZ-axis movement buttons, [PTP] button, [Brake] button

Pressing the arrow buttons moves the squeegee head vertically. When the [Step Mode] button is in the depressed state,

the squeegee head moves at the specified step stroke each time the arrow buttons are pressed.

Pressing the [PTP] button displays the "PTP" dialog box. You can directly specify the position (height) where you want to

move the squeegee head. The current position is displayed in the "SZ (mm)" box.

The [Brake] button turns the SZ-axis brake on or off.

3. [Step Mode] button

Press this button to set axis movement to "step mode (inching mode)". (The button will remain depressed until you press

it again to exit "step mode".)

Specify the step stroke (inching stroke) with the arrow button or enter it directly in the "Step Stroke" box.

4. "Speed (%)" box

Select the speed to move the unit.

TIP

Operation of buttons on the other tabs is basically the same. The [Y/Z], [SY/SZ], [SR] and [PU] tab have a [Brake] button

that turns the motor brake on or off.

CAUTION

The X-axis is operated in synchronization with the X1, X2 and Z axes. If each axis is used independently, moving to a

target position may become difﬁcult. To move on the X-axis and R-axis, use the [PTP] button.

6-20

Other functions

4.2 [Unit] - [Conveyor] tab screen

The [Unit] - [Conveyor] tab screen allows you to manually operate each conveyor unit and check the status of

the conveyor sensors and I/O signals on the graphic view. The function of each button is described below.

[Unit]-[Conveyor] tab screen

64619-L3-10

Operation buttons in upper row (from left)

[SW. Prod. Position] button

Moves the board clamp table to the front and the squeegee head to the

inner side.

[Convey-in] button Carries a board in on the board clamp table.

[Convey-out] button Carries the board out from the board clamp table.

[Left], [right] buttons Switches on the conveyor motor so the conveyor moves to the left or right.

[Conv. 3 Stopper] button Raises or lowers the left stopper when viewed from the front of the machine.

[Main Stopper] button Raises or lowers the main stopper.

[Main Stopper Fore/Back] button Moves the main stopper forward or backward in the Y direction.

[Conv. 1 Stopper] button

Raises or lowers the right stopper when viewed from the front of the

machine.

[Flap] button Actuates the board flap.

Operation buttons in lower row (from left)

[Axis] button Opens the "Move Axis" screen. (See "4.1" in this chapter.)

[Width] button Changes the conveyor width.

[Main Stopper Position] button Moves the main stopper according to the board length.

[Low Left], [low Right] buttons

Switches on the conveyor motor so the conveyor moves at slow speed to

the left or right.

[Board Fix] button Actuates the effective board clamp units to clamp a board in print position.

[Push Up] button Raises or lowers the push-up plate.

[Board Vacuum] button Turns the vacuum board gripper on or off. (option)

[Board Press] button Turns the board press unit on or off. (option)

[Edge Clamp] button Turns the edge clamp on or off.

6-21

Other functions

4.3 [Unit] - [Mask] tab screen

The [Unit] - [Mask] tab screen allows you to manually operate the mask vacuum gripper and check the status

of the mask sensors on the graphic view. The function of each button is described below.

[Unit]-[Mask] tab screen

1 3

64620-L3-00

Operation buttons

Button name Function

1 Axis Opens the "Move Axis" screen. (See "4.1" in this chapter.)

2 Mask Vacuum Turns the mask vacuum gripper on or off.

3 Fiducial Correction Moves the vision camera to recognize mask fiducial marks.