YSP_Users_E.pdf - 第36页
Chapter 8 Inspection and maintenance 1. Precautions 8-1 2. Inspection and maintenance 8-2 2.1 Daily inspection 8-2 2.2 Periodic inspection (W eekly/Monthly) 8-3 2.2.1 Parts to be replaced during periodic replacement 8-3 …
2. Pattern matching 6-9
2.1 Pattern registration 6-10
2.2 Using the pattern matching 6-15
3. Matrix pin arrangement 6-16
4. Manual operation 6-17
4.1 "Move Axis" screen 6-18
4.2 [Unit] - [Conveyor] tab screen 6-20
4.3 [Unit] - [Mask] tab screen 6-21
4.4 [Unit] - [Squeegee] tab screen 6-22
4.5 [Unit] - [Cleaner] tab screen 6-23
4.6 [Unit] - [I/O] tab screen 6-24
Chapter 7 Replacing the consumable parts
1. Precautions 7-1
2. Replacing the squeegee 7-2
2.1 Replacing the unit 7-2
2.2.1 Metal squeegee scraper 7-3
2.2.2 Urethane squeegee scraper 7-4
3. Replacing the cleaning gauze roll 7-6
3.1 Using the same roll size 7-7
3.2 Changing the roll size 7-8
4. Refilling the cleaning solvent 7-10
4.1 Precautions when handling cleaning solvent 7-10
4.2 Refilling the cleaning solvent 7-10
4.3 Long-term storage tasks 7-12
5. Suction-blower unit 7-13
5.1 Replacing the filter 7-13
5.2 Replacing the blower hose 7-14
5.3 Cleaning and replacing the filter for the mask vacuum chuck 7-16
6. Replacing the conveyor belt 7-17
6.1 Board carry-in and carry-out conveyors 7-17
6.2 Board clamp unit (board clamp table) 7-20
Chapter 8 Inspection and maintenance
1. Precautions 8-1
2. Inspection and maintenance 8-2
2.1 Daily inspection 8-2
2.2 Periodic inspection (Weekly/Monthly) 8-3
2.2.1 Parts to be replaced during periodic replacement 8-3
2.2.2 Recommended grease 8-3
2.2.3 List of periodic inspection checkpoints 8-4
2.2.4 Parts recommended for periodic replacement 8-6
2.3 Adjusting the conveyor belt tension 8-7
2.3.1 Board carry-in and carry-out conveyors 8-7
2.3.2 Board clamp unit (board clamp table) 8-9
2.4 Inspecting and cleaning the air/mist filters 8-11
3. List of lubrication locations 8-13
3.1 X-, Y-, and Z-axis 8-13
3.1.1 X1-axis and X2-axis 8-13
3.1.2 Y-axis 8-14
3.1.3 Z-axis 8-14
3.2 Printing head 8-15
3.2.1 SY-axis 8-15
3.2.2 SZ-axis 8-15
3.3 Conveyor unit 8-16
3.3.1 PU-axis 8-16
3.3.2 MS-axis 8-16
3.3.3 W-axis (Conveyor auto width adjustment) 8-17
3.4 Vision camera unit 8-18
3.4.1 CX-axis 8-18
Appendix
1. Specifications A-1
1.1 Air regulator unit A-1
1.1.1 Air supply A-1
1.2 Connection between machines A-2
1.2.1 PREVIOUS INTERFACE connector A-3
1.2.2 NEXT INTERFACE connector A-4
1.3 Power connection terminals A-5
2. Compatible masks A-6
2.1 Mask size and mask stopper pin position A-6
2.2 Mask frame dimensions and mask standard position A-7
3. Inverter (suction unit) A-8
4. Board support jig combinations A-9
Printing guide
1. Flow of printing condition setting E-1
2. Data and condition setting E-2
2.1 Material and setup information E-2
2.2 Alignment offset setting E-4
2.3 Rolling E-5
2.4 Printing and production conditions E-6
3. Details of each parameter item E-7
3.1 Board clamp E-7
3.1.1 Edge clamp pressure E-7
3.1.2 Backup jig E-8
3.2 Board and mask mark recognition (Mark position) E-8
3.3 Alignment offset E-8
3.4 Squeegee (Rolling) E-9
3.4.1 Squeegee speed E-9
3.4.2 Squeegee pressure E-9
3.4.3 Attack angle (degree (°)) E-9
3.5 Solder supply interval E-10
3.6 Detach pattern E-10
3.6.1 Board separation speed E-10
3.6.2 Board separation distance E-11
3.7 Cleaning E-11
3.7.1 Cleaning interval E-11
3.7.2 Cleaning repeat E-11
3.7.3 Cleaning speed E-11
4.
Causes of troubles predicted from symptoms (Appendix)
E-12
4.1 Positional deviation E-12
4.2 Blur E-12
4.3 Insufficient filling E-12
4.4 Solder spread, solder bridge E-13
4.5 Scraping trouble E-13
4.6 Solder enlargement E-13
4.7 Solder chipping, mask remaining E-13
Index