YSP_Users_E.pdf - 第223页

7-14 7 Replacing the consumable parts 5.2 Replacing the blower hose IT o replace the blower hose, follow the steps below . e 1 Pr ess the emergency stop button. 2 Open the rear co ver of the machine. 3 Remo ve the blower…

100%1 / 278
7-13
7
Replacing the consumable parts
5. Suction-blower unit
The suction-blower unit is always operated even when the machine is in emergency stop. It is therefore
necessary to clean and replace the filter and replace the blower hose periodically.
5.1 Replacing the filter
To clean and replace the filter, follow the steps below.
e
1
Press the emergency stop button.
2
Open the lower cover on the rear
of the machine.
3
Protect the inverter main unit.
Cover the inverter main unit with a cloth rag
to prevent entry of dust.
63021-L3-00
4
Remove the cover.
Remove two screws from the upper portion
with a Phillips screwdriver. The cover is then
opened like it falls down.
5
Take out the filter and clean it.
Take out the ring filter and blow the air from
the inside of the filter with an air gun.
63022-L3-00
6
Return the filter to its original
position.
Insert the filter to its original position and
close the cover.
Removing the cover
Step 3, 4
Phillips screwdriver Cloth ragCover
Taking out the filter
Step 5
Filter
7-14
7
Replacing the consumable parts
5.2 Replacing the blower hose
ITo replace the blower hose, follow the steps below.
e
1
Press the emergency stop button.
2
Open the rear cover of the
machine.
3
Remove the blower hose from the
blower.
1. Move the board clamp table on the
Y-axis to the front side of the machine.
2. Remove the hose band with a flat-blade
screwdriver and remove the blower hose
from the vacuum pipe.
3. Loosen the mounting bolts on the hose
clamps (2 bolts on each clamp) with an
Allen wrench (4mm).
4
Open the front cover of the
machine.
5
Remove the blower hose from the
cleaner.
1. Pull the cleaner head to the front of the
machine.
2. Loosen the hose band with a flat-blade
screwdriver and remove the blower hose
from the joint.
3. Pull out the blower hose.
63723-L3-00
6
Insert a new blower hose from the
cleaner side.
1. Insert the new blower hose and pass it
through the hose clamps.
n
NOTE
Insert the blower hose so that it smoothly bends
upward.
2. Connect the blower hose to the joint and
tighten the hose band with the flat-blade
screwdriver to clamp the hose.
7
Temporarily connect the blower
hose on the blower to the vacuum
pipe.
1. Move the board clamp table on the
Y-axis to the front side.
2. Temporarily connect the blower hose to
the vacuum pipe.
63724-L3-00
8
Check the blower hose position
while viewing from the cleaner
side.
Move the cleaner head in the Y direction
and check that the blower hose is
positioned straight on the hose guide.
Removing the blower hose
Step 5
Hose band
Hose band
Hose clamp
Mounting bolt (2 bolts on each clamp)
Joint
Vacuum pipe
Blower hose
Inserting the blower hose
Step 6,7
Hose guide
Blower hose
Vacuum pipe
Hose clamp
Joint
7-15
7
Replacing the consumable parts
9
Clamp the blower hose.
1. Using the flat-blade screwdriver, tighten
the hose band on the vacuum pipe to
clamp the hose.
2. Using the Allen wrench (4mm), tighten
the mounting bolts on the hose clamps (2
bolts on each clamp) to clamp the
blower hose.
0
Close the front and rear covers of
the machine.