YSP_Users_E.pdf - 第224页

7-15 7 Replacing the consumable parts 9 Clamp the blow er hose. 1. Using the flat-blade screwdriver , tighten the hose band on the vacuum pipe to clamp the hose. 2. Using the Allen wrench (4mm), tighten the mounting bolt…

100%1 / 278
7-14
7
Replacing the consumable parts
5.2 Replacing the blower hose
ITo replace the blower hose, follow the steps below.
e
1
Press the emergency stop button.
2
Open the rear cover of the
machine.
3
Remove the blower hose from the
blower.
1. Move the board clamp table on the
Y-axis to the front side of the machine.
2. Remove the hose band with a flat-blade
screwdriver and remove the blower hose
from the vacuum pipe.
3. Loosen the mounting bolts on the hose
clamps (2 bolts on each clamp) with an
Allen wrench (4mm).
4
Open the front cover of the
machine.
5
Remove the blower hose from the
cleaner.
1. Pull the cleaner head to the front of the
machine.
2. Loosen the hose band with a flat-blade
screwdriver and remove the blower hose
from the joint.
3. Pull out the blower hose.
63723-L3-00
6
Insert a new blower hose from the
cleaner side.
1. Insert the new blower hose and pass it
through the hose clamps.
n
NOTE
Insert the blower hose so that it smoothly bends
upward.
2. Connect the blower hose to the joint and
tighten the hose band with the flat-blade
screwdriver to clamp the hose.
7
Temporarily connect the blower
hose on the blower to the vacuum
pipe.
1. Move the board clamp table on the
Y-axis to the front side.
2. Temporarily connect the blower hose to
the vacuum pipe.
63724-L3-00
8
Check the blower hose position
while viewing from the cleaner
side.
Move the cleaner head in the Y direction
and check that the blower hose is
positioned straight on the hose guide.
Removing the blower hose
Step 5
Hose band
Hose band
Hose clamp
Mounting bolt (2 bolts on each clamp)
Joint
Vacuum pipe
Blower hose
Inserting the blower hose
Step 6,7
Hose guide
Blower hose
Vacuum pipe
Hose clamp
Joint
7-15
7
Replacing the consumable parts
9
Clamp the blower hose.
1. Using the flat-blade screwdriver, tighten
the hose band on the vacuum pipe to
clamp the hose.
2. Using the Allen wrench (4mm), tighten
the mounting bolts on the hose clamps (2
bolts on each clamp) to clamp the
blower hose.
0
Close the front and rear covers of
the machine.
7-16
7
Replacing the consumable parts
5.3 Cleaning and replacing the filter for the mask vacuum chuck
n
Required tools
• Phillips screwdriver
• Replacement filter (KGR-M9933-F0X FILTER, SPARE
)
• Air blow tool (option)
e
1
Press the emergency stop button.
To ensure the work safety, be sure to put the
machine in the emergency stop status.
2
Move the print table into the back.
Move the print table into the back manually
so that it becomes easier to work on the
filter unit.
3
Open the upper door.
Open the upper door at the rear side of the
machine.
4
Remove the filter unit.
Remove the filter unit from the air hose.
63725-L3-00
5
Take the filter out of the filter unit.
Turn the joint cap, which has marks L (Lock)
and O (Open) on it, to the “O” direction and
take the filter out of the transparent case.
6
Clean the filter.
Use the air blow tool to blow away dust and
impurities trapped in the filter, by blowing air
from the inside and also from the outside. If
the filter is excessively dirty and cannot be
cleaned, replace it with a new filter.
7
Reattach the filter unit.
1. Put the filter into the transparent case
and tighten the removed joint cap by
turning it to the “L” direction.
2. Connect the air hose so that the arrow
mark (
▲
) on the filter unit is located on
the ejector side.
Filter unit
Backup unit
joint cap
Filter Transparent caseL and O marks
Step 4,5
Filter unit