YSP_Users_E.pdf - 第32页
General Contents About this manual 1. About this manual i 1.1 Revision record i 1.2 Contents of each chapter ii 1.3 Page layout iii Chapter 1 Par t names and functions 1. YSP main unit 1-1 2. Operation panels and data in…
xxviii
Safety instructions
3.4 Label positions
The following warning/caution labels are attached to the YAMAHA products to ensure safe and correct use.
Check that the information on each label is clearly legible and comply with the instructions.
For safety precautions other than those on the labels shown in this section, see the instructions in "1. Safety".
n
NOTE
Basically, labels are attached to the positions shown below, although they may differ slightly depending on the
machine model.
n
NOTE
When connecting power to this equipment, refer to "Power connection terminals" described in the appendix of the
maintenance manual or user's manual.
Warning/caution labels
YSP
■ Open/close cover inner side
■ Cover cover
■ Cover cover inner side
■ Main switch
■ Conveyor opening
(left and right) ,
Conveyor extension
on exit side (left and right)
■ Printing table/mask clamp
(inside safety cover)
■ Left side and Right side
■ Cleaning alcohol (behind front cover)
■ Behind front cover
■ Lower panels (front and rear)
■ Panel inner side
■ Vision camera unit
93201-L3-30
General Contents
About this manual
1. About this manual i
1.1 Revision record i
1.2 Contents of each chapter ii
1.3 Page layout iii
Chapter 1 Part names and functions
1. YSP main unit 1-1
2. Operation panels and data input units 1-4
2.1 Operation panel buttons 1-5
2.2 Keyboard and mouse 1-6
2.3 Liquid crystal touch screen (option) 1-6
3. Printing section 1-7
3.1 Squeegee head and printing table 1-7
3.2 3S squeegee 1-8
3.3 Double squeegee (option) 1-9
4. Conveyor unit 1-10
4.1 Board clamp unit (board clamp table) 1-10
4.2 Board support 1-11
4.3 Board carry-in and carry-out conveyors 1-15
4.4 Extended exit conveyor (option) 1-15
4.4.1 MANUAL mode 1-16
4.4.2 AUTO mode 1-17
5. Cleaning unit 1-18
5.1 Cleaning unit 1-18
5.2 Suction unit 1-19
6. Camera unit 1-20
7. Servo-controlled axes 1-21
Chapter 2 Basic operations
1. Canceling emergency stop and clearing an error 2-1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-2
1.3 Typical errors and troubleshooting 2-3
EUL3181200
2. Starting and stopping the machine 2-8
2.1 Inspecting before operation 2-9
2.2 Starting the machine 2-10
2.3 Turning off the machine 2-12
3. Operation screen description 2-14
3.1 Basic configuration of operation screen 2-14
3.2 Various buttons and parameter input grids 2-15
Chapter 3 Daily operation
1. Overview 3-1
2. Starting and warming up the machine 3-2
3. Selecting the board data 3-4
4. Changing the conveyor unit setup 3-5
5. Setting up the mask and squeegee 3-7
5.1 Using the mask adaptor 3-9
6. Rolling operation 3-11
7. Starting board production 3-14
8. Finishing board production 3-21
Chapter 4 Creating and setting the data
1. Creating new data 4-1
2. Basic data setting 4-3
2.1 Configuration of [Basics] tab screen 4-3
3. Board data setting 4-5
3.1 Board marks and parameter setting 4-5
3.2 Board data detail setting 4-10
4. Mask data setting 4-13
4.1 Mask marks and parameter setting 4-13
4.2 Mask data detail setting 4-17
5. Squeegee data setting 4-19
5.1 Squeegee detail setting 4-25
6. Cleaner data setting 4-28