00191025-01.pdf - 第444页
SIPLACE 80S/F/G User’s Manual 9 Maintenance Edition 07/97 from S oftware Version SR.010.xx 9.6 IC Head (SIPLA CE 80F) 9 - 85 Sequence of work in Fig. 9. 6.9 A C lean the a nnular surfac es all ov er with a dry brush. B D…
9 Maintenance SIPLACE 80S/F/G User’s Manual
9.6 IC Head (SIPLACE 80F) Edition 07/97 from Software Version SR.010.xx
9 - 84
Fig. 9.6.9 Maintaining the nozzles
Key to
Fig. 9.6.9
(The item numbers of the nozzles and diaphragms will be found in Tab. 9.6.1, Page 87.)
1 Maintenance of the nozzles with diaphragm
2 Nozzle, type 419
3 Diaphragm
4 Sleeve
5 Nozzle, type 418
6 Enlarged view
7 Maintenance of the nozzles without diaphragm
8 Nozzle, type 417
9 Nozzle, type 416
SIPLACE 80S/F/G User’s Manual 9 Maintenance
Edition 07/97 from Software Version SR.010.xx 9.6 IC Head (SIPLACE 80F)
9 - 85
Sequence of work in
Fig. 9.6.9
A Clean the annular surfaces all over with a dry brush.
B Dry clean the annular surface of the sleeve.
C Rub the annular surface of the diaphragm sparingly with talcum.
D Clean the suction hole.
E Check the suction surface.
9.6.6.3 Replacing the Diaphragm of the Nozzles
●
Replace the diaphragm if damaged. All relevant details are shown in the following diagram.
Fig. 9.6.10 Replacing the diaphragm of the nozzles
Key to
Fig. 9.6.10
(The item numbers of the nozzles and diaphragms will be found in Tab. 9.6.1, Page 87.)
1 Removing the diaphragm (enlarged view)
2 Diaphragm
3 Sleeve
4 Annular surface
9 Maintenance SIPLACE 80S/F/G User’s Manual
9.6 IC Head (SIPLACE 80F) Edition 07/97 from Software Version SR.010.xx
9 - 86
5 Diaphragm: item no. 309 458
6 Nozzle: item no. 309 456
7 Diaphragm: item no. 307 052
8 Nozzle: item no. 307 051
Sequence of work in
Fig. 9.6.10
A Pull off the sleeve.
B Remove the diaphragm.
C Clean the sleeve with alcohol and dry it before refitting.
D Rub the annular surface of the new diaphragm sparingly with talcum, keeping it absolutely free of grease.
∆
!
Slide the sleeve back in as far as it will go.
9.6.6.4 Inserting Nozzles into the Nozzle Changer
●
After maintenance insert the nozzles by hand into their correct assigned places (by referring to the notes
you took when you removed them ) in the nozzle changer.
●
Insert the nozzle removal tool into each nozzle in turn and turn the nozzle anticlockwise until it locks in the
nozzle changer. Lift the tool vertically upwards and out.
●
Close the safety hoods and swivel doors and switch the machine on.
●
Have the allocations of nozzles to garage numbers displayed by making the following selection :
Single functions
→
Gantry 1
→
Nozzle configuration IC head
NOTE
You can only use this function when you have returned the current nozzle not by hand but, as described,
by using the
Return nozzle
function.
●
A table will be shown on the screen with the garage numbers (pick-up location numbers) and the actual
and programmed occupancies. Insert the nozzles into the nozzle changer in accordance with the ACTUAL
assignments.
●
Check to make sure the nozzles are properly latched.
NOTE
If the nozzles are not properly latched this will lead to errors in picking up the nozzle, while incorrectly
assigned nozzles will result in component pick-up errors.
●
At the start of placement the current nozzle as specified in the placement program will be picked up.